Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Nim
Operating Systems AIX Nim Post 302276035 by bakunin on Tuesday 13th of January 2009 01:14:51 AM
Old 01-13-2009
I do not think there is such a thing and probably can't be: NIM is a rather complex environment and for it to "work properly from both master as well as client side" it takes several independent criteria to be met: working network connections, several configurations of various sorts on both the client and the server, a working set of server resources, etc., etc.

While it is possible to test and trace all these things one after the other i do not think there is one "sure-shot single command" to test all these criteria to be met at once.

I hope this helps.

bakunin
 

10 More Discussions You Might Find Interesting

1. AIX

migrate NIM server through NIM installation

I try to migrate a NIM server from one server to another. I try to do a mksysb on NIM server restore the NIM server's mksysb to a client through NIM installation shutdown NIM server start newly installed client as NIM server Does anyone do this before? who can give me some suggestion? (1 Reply)
Discussion started by: yanzhang
1 Replies

2. AIX

NIM errors

Hello all, I have a NIM master already up and running. When I try to add a client to the NIM environment (from client side), I get the following errors: 1) 0042-376 niminit: This command cannot be executed on a NIM master unless the "is_alternate" attribute is specified. (I never... (5 Replies)
Discussion started by: solaix14
5 Replies

3. AIX

NIM Questions

I have been trying to increase the NIM usage in my AIX environment especially for patching, got few questions 1. If I have a service pack available in the nim server, how do I define that particular directory as an LPP source, without again copying it somewhere else ie I want to define that... (5 Replies)
Discussion started by: balaji_prk
5 Replies

4. AIX

Nim

Hello everyone I have two questions. 1.-The NIM and EZNIM are the same. 2.-If I have in one partition NIM installed I need to install EZNIM or I need to unistall NIM and then install EZNIM. Thanks for your comments. (2 Replies)
Discussion started by: lo-lp-kl
2 Replies

5. AIX

Back up a client NIM from nim master

Hello everyone Im trying to backup a nim client from nim master but I got this message COMMAND STATUS Command: failed stdout: yes stderr: no Before command completion, additional instructions may appear below. 0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies

6. AIX

Nim

Hello I would like to hear your opinions about shell and nimsh I install the nim master on a server and and client nim on others servers. I backup this clients with the NIM master. When Im trying to install the clients with the option nimsh (communication protocol) send me an error ... (1 Reply)
Discussion started by: lo-lp-kl
1 Replies

7. AIX

Help Nim

Hi everybody.. I need help with nim .. I am install nim master in may ambient. # lsnim -l master master: class = machines type = master max_nimesis_threads = 20 comments = machine which controls the NIM environment global_export ... (2 Replies)
Discussion started by: cwb
2 Replies

8. AIX

NIM : remove nim client info from the client

Hi. I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ? Tks (2 Replies)
Discussion started by: stephnane
2 Replies

9. AIX

Problem in communication nim client with nim master

Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies

10. AIX

How to know NIM name from NIM client?

Friend's, I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client? All leads to the answer would be much appreciated, many thanks! -- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies

LEARN ABOUT CENTOS

ucmatose

UCMATOSE(1)							     librdmacm							       UCMATOSE(1)

NAME

       ucmatose - RDMA CM connection and simple ping-pong test.

SYNOPSIS

       ucmatose [-s server_address] [-b bind_address] [-c connections]
		 [-C message_count] [-S message_size]
       ucmatose -s server_address [-b bind_address] [-c connections]
		 [-C message_count] [-S message_size] [-t tos]

DESCRIPTION

       Establishes  a  set  of	reliable RDMA connections between two nodes using the librdmacm, optionally transfers data between the nodes, then
       disconnects.

OPTIONS

       -s server_address
	      The network name or IP address of the server system listening for connections.  The used name or address must  route  over  an  RDMA
	      device.  This option must be specified by the client.

       -b bind_address
	      The local network address to bind to.

       -c connections
	      The number of connections to establish between the client and server.  (default 1)

       -C message_count
	      The number of messages to transfer over each connection.	(default 10)

       -S message_size
	      The size of each message transferred, in bytes.  (default 100)

       -t tos Indicates  the  type  of service used for the communication.  Type of service is implementation dependent based on subnet configura-
	      tion.

       -m     Tests event channel migration.  Migrates all communication identifiers to a different event channel for disconnect events.

NOTES

       Basic usage is to start ucmatose on a server system, then run ucmatose -s server_name on a client system.

       Because this test maps RDMA resources to userspace, users must ensure that they have available system resources and permissions.   See  the
       libibverbs README file for additional details.

SEE ALSO

       rdma_cm(7), udaddy(1), mckey(1), rping(1)

librdmacm							    2007-05-15							       UCMATOSE(1)
All times are GMT -4. The time now is 02:23 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy