redirect routing on non-default interface Post: 302274348

7 More Discussions You Might Find Interesting

1. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

2. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

3. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

4. Solaris

Traffic routing through wrong interface

Solaris-9 server is having one primary IP 10.41.161.14 on qfe0 and 10.41.116.0 on qfe3:1. Traffic is going through virtual interface instead of physical interface. How should I force traffic to go with primary interface. root@smtsrvn01:/# netstat -nr Routing Table: IPv4 Destination ...

5. IP Networking

Linux load balancer ping redirect to other interface

Im configuring centos with load balance with ip route and ip rule Eth0 192.168.1.5 Eth1 192.168.5.128 # ip route 192.168.5.0/24 dev eth1 scope link src 192.168.5.128 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.5 169.254.0.0/16 dev eth1 scope link # ip route show...

6. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

7. IP Networking

Port based multi interface routing

Hello, I wanted to setup routing certain traffic (http/s) out via a second (faster) interface, like described in the following docs (may not post urls): linux-ip.net /html/adv-multi-internet.html thegeekstuff.com /2014/08/add-route-ip-command/ I already had this working years ago on...

LEARN ABOUT HPUX

mrinfo

mrinfo(1M)																mrinfo(1M)

NAME

       mrinfo - Multicast Routing Configuration Information Tool

SYNOPSIS

       debuglevel] retries] timeout] [ multicast-router ]

DESCRIPTION

       requests  the configuration information from the multicast-ourter, and prints the information to the standard out.  multicast-router can be
       either an IP address or a system name.  sends out the ASK_NEIGHBORS igmp  message  to  the  specified  multicast-router,  when  the  router
       receives  the request, it sends back its configuration information. If the multicast-router is not specified, the request is sent the local
       router.

       The the configuration information for each interface is printed in the following format:

       If there are multiple neighbor routers on one interface, they will all be reported on the output.  The possible values for flag are:

       Neighbors are reached via tunnel.

       The tunnel uses IP source routing.

       The interface is down.

       The interface is administratively disabled for multicast routing.

       The local router is the querier of the subnet.

       Please see mrouted(1M) for and

       The command line options are:

       Sets the level for printing out the debug message. The default is 0,
		     only error and warning messages will be printed. Debug level three prints most the messages.

       Sets the retry times to pull the routing daemon for information. The
		     default is 3.

       Specifies the timeout value in seconds for waiting the reply. The default value
		     is 4.

EXAMPLE

       The following is an example of quering the multicasting configuration from the local routing daemon.

	      127.0.0.1 (localhost) [version 3.3]:
		15.13.106.144 -> 15.13.106.145 (hpntcbs.cup.hp.com) [10/1/querier]
		193.2.1.39 -> 0.0.0.0 (all-zeros-broadcast) [1/1/disabled]
		15.13.106.144 -> 15.255.176.33 (matmos.hpl.hp.com) [10/1/tunnel]
		15.13.106.144 -> 15.17.20.7 (hpspddc.vid.hp.com) [10/1/tunnel/down]

   Note
       must be run as root.

AUTHOR

       was developed by Van Jacobson.

SEE ALSO

       mrouted(1M), map-mbone(1M).

																	mrinfo(1M)