12-28-2008
does it work after you unplug the new disk?
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I enquired before about adding another disk to an ultra 10...
and was told it was possible...
Well - since then I got my hands on another ultra 10 - and have taken the disk out of that one...
I should be able to connect it up - but I am wondering - should this be mounted in any partiulcar... (2 Replies)
Discussion started by: frustrated1
2 Replies
2. Solaris
Dear all ,
I am new to sun cluster and i having a problem adding a disk to a disk group .
My platfrom consists of a clustered E6900 SUN server and an EMC DX1000 storage .
the disk group that iam trying to add the disk to is shared group ,
whwen i run vxdisk list i get in status "online... (2 Replies)
Discussion started by: ppass
2 Replies
3. AIX
Hi,
I'm getting the errors below in the errpt report for a IBM Blade server. I'm guessing there's a problem with one of the disks but don't know how I can confirm this. Can anyone offer any suggestions?
Regards
Gareth (4 Replies)
Discussion started by: m223464
4 Replies
4. HP-UX
Hi dear(s)
Can u explain how to add a disk through lvm with commands.
I need to add a 9 gb scsi HS disk to a Hp D class 9000 server. (2 Replies)
Discussion started by: sreekumar.R
2 Replies
5. Filesystems, Disks and Memory
Wellcomes All,
some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
Discussion started by: thekarsillo
1 Replies
6. Filesystems, Disks and Memory
Hello,
I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future.
Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies
7. UNIX Desktop Questions & Answers
Hi there! I am installing Unixware 7.1 to a new server. We usually use SCSI hard for this but since this will be used only for testing, I decided to use an 80GB IDE hard disk. I was able to successfully load the unix but found out that the 80GB hard disk was not maximized. The total hard disk... (1 Reply)
Discussion started by: limpinmd
1 Replies
8. Filesystems, Disks and Memory
Recently added a disk to a clariion array system, binded it as a raid 5, now I have no clue how to see it in dg-unix. I want to add it to a current filesystem, and now i'm down river without a paddle. (0 Replies)
Discussion started by: danceofillusion
0 Replies
9. SCO
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies
10. AIX
Hi,
On P5 I would like to add hard drive, currently 2 hard disk are already exists, would like to add one more,
2 Slots are emtpy, I would like to know how to find out wheather adapter is attached to that 2 free slot using command. (7 Replies)
Discussion started by: manoj.solaris
7 Replies
LEARN ABOUT HPUX
vxreattach
vxreattach(1M) vxreattach(1M)
NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS
-b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO
vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)
VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)