I have the primary set up, but cannot get the secondary box to answer a query. Here is the message I get:
> nslookup dfwnet1 10.26.38.41
*** Can't find server name for address 10.26.38.41: Non-existent host/domain
*** Default servers are not available
10.26.38.41 is the IP of the secondary... (3 Replies)
:cool:
I want to use 2 tcp applications in SCO 5.05 senerio I am using
VisionFS 3.1 and I need to set it up as a secondary tcp app. I follow the profeditoir and change the tcp port from the primary port (139) to any other number below port 1024 and then restart the VisionFS server it is still... (2 Replies)
Wellcomes All,
some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
This is one our office BOX
Sun Microsystems Inc. SunOS 5.10 Generic January 2005
Kisses% rlogin pebblz01 -l adminID
Password:
Last login: Sat Feb 14 01:11:36 from Kisses
Please enter your own login id and password.
Your login: I_rule
Your password:xxxxx
From the above... (3 Replies)
hosta(eth0)----|switch|---(eth0)hostb
say hosta and hostb both connect to a swtich using eth0 with public IP addresses, and I add secondary and private IP on hosta and hostb's same eth0 interfaces.
So in order for them to reach each other, do I need to config the switch? (3 Replies)
hi guys
I am doing some testing for DNS
I got a master DNS(192.168.2.10) and I setup a slave DNS(192.168.2.11) but when I shutdown the Master DNS my linux client cannot resolve using the slave
any idea way?
This is the named.conf
options
{
query-source port 53;
directory... (9 Replies)
Hi
In Linux I set Secondary Logging in the way below.
1. We perform this by adding below lines into
/root/.bashrcfile :
# secondary logging beginexport HISTSIZE=600000export HISTFILESIZE=600000export HISTTIMEFORMAT="%F %T %z "export HISTFILE=/root/.bashhist/root_history-$(who am i | awk... (4 Replies)
Hi All,
My Servers are enabled with a secondary authentication of login. Whenever we are logging in to the servers with a common id it is asking like something " Enet your personal id and password" which has been created by UNIX admins previously.
Just curious how to achieve this... (1 Reply)
This has got to be the system from hell. Once again, on the RP4440 (after the supplier replaced the entire box due to the bad RTC battery), finally have it all reloaded with the packages the developers need. The last thing is to add the secondary disk to the OS.
BCH sees both OS and secondary... (2 Replies)
Discussion started by: mrmurdock
2 Replies
LEARN ABOUT LINUX
diskscan
diskscan(1M) System Administration Commands diskscan(1M)NAME
diskscan - perform surface analysis
SYNOPSIS
diskscan [-W] [-n] [-y] raw_device
DESCRIPTION
diskscan is used by the system administrator to perform surface analysis on a portion of a hard disk. The disk portion may be a raw parti-
tion or slice; it is identified using its raw device name. By default, the specified portion of the disk is read (non-destructive) and
errors reported on standard error. In addition, a progress report is printed on standard out. The list of bad blocks should be saved in a
file and later fed into addbadsec(1M), which will remap them.
OPTIONS
The following options are supported:
-n Causes diskscan to suppress linefeeds when printing progress information on standard out.
-W Causes diskscan to perform write and read surface analysis. This type of surface analysis is destructive and should be invoked
with caution.
-y Causes diskscan to suppress the warning regarding destruction of existing data that is issued when -W is used.
OPERANDS
The following operands are supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?[ps]?. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO addbadsec(1M), disks(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the diskscan, addbad-
sec(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS format utility; however, to label, ana-
lyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 diskscan(1M)