Hi ,
could any one suggest me that how to determine if the first field is numeric and if it is greater than another number then from that point everything else should be printed using awk.
I have tried this
:
awk -v xxxx=$xxxxx '
BEGIN {
enable=0
}
{
print $1
if ( ( $1 !~ "^*$" ... (5 Replies)
Hi all,
I have 2 files. One contains only 1 column and other one contains 2 columns, let say 1_col.txt and 2_col.txt respectively. Here, I will try to explain with an example.
Input files :
1_col.txt 2_col.txt
a a b
x a c
p ... (5 Replies)
Hi All,
I have to match each row in file 1 with 1st row in file 2 and print the corresponding column from file2. I am trying to use an awk script to do this. For example
cat File1
X1
X3
X4
cat File2
ID X1 X2 X3 X4
A 1 6 2 1
B 2 7 3 3
C 3 8 4 1
D 4 9 1 1 (3 Replies)
Hi
I am checking status of sftp in Health check script, sftp command is used to connect the server with secure RSA key, which is successfully get connected most of the time but in some case if RSA key ask for password then I need to exit sftp command after few second and continue to run... (1 Reply)
Hi, all
I need your help and suggestions.
I want to print particular strings in a field of a csv file and show them in terminal. Here is an example of the csv file.
SourceFile,Airspeed,GPSLatitude,GPSLongitude,Temperature,Pressure,Altitude,Roll,Pitch,Yaw... (7 Replies)
Want to get the remaining line after pattern match Here it starts - executed commands : - pattern to identify 100:27:500:1:34:END
Required output:100:27:500:1:34:END
awk '{if(/pattern to identify/) print $2}' < file
I have used above code and it not giving... (3 Replies)
Hi All,
I am having a text file like below
ERROR - Not a valid
ID : 123
ERROR - Not a valid
hello
ID : 124
SUCCESS - Valid
ID : 12
I need to display like below after reading the file if it finds the error keyword
along with displaying this first line when error pattern... (10 Replies)
Hello there
I'd like to make a copy of 2nd column and have it printed in place of column 1. Remaining columns are needed as it.
test data:
ProbeSet GeneSymbol X22565285 X22566285
ILMN_1050008 MYOCD 6.577 7.395
ILMN_1050014 GPRC6A 6.595 6.668
ILMN_1050017 ... (2 Replies)
Hello Folks,
I have an requirement, where i need to get total count of the file based on creation date with there filename selected pattern.
Filename: MobileProtocol.20171228T154200.157115.udr
I want to get the count of files created on each day based on a pattern find.
find . -type... (7 Replies)
Discussion started by: sadique.manzar
7 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)