12-18-2008
no such interface
Hi Community,
I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output:
# ifconfig hme0 <ip_address> netmask <mask> plumb
#ifconfig: plumb: hme0: no such interface
I've the same thing with dhcp service.
could you provide any solution please? it is very urgent
Thank you for your availability
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
3. IP Networking
Hi,
ifconfig -a return:
eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A
inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0
... (5 Replies)
Discussion started by: djbuly
5 Replies
4. UNIX for Advanced & Expert Users
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies
5. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
inetutils-ifconfig
IFCONFIG(1) User Commands IFCONFIG(1)
NAME
ifconfig - configure network interfaces
SYNOPSIS
ifconfig [OPTION...]
DESCRIPTION
NAME [ADDR] [broadcast BRDADDR] [pointopoint|dstaddr DSTADDR]
[netmask MASK] [metric N] [mtu N] [txqueuelen N] [up|down] [FLAGS]
Configure network interfaces.
-a, --all
display all available interfaces
-A, --address=ADDR
set interface address to ADDR
-B, -b, --broadcast=ADDR, --brdaddr=ADDR
set broadcast address to ADDR
-d, -p, --dstaddr=ADDR, --peer=ADDR
set destination (peer) address to ADDR
--down shut the interface down
--format=FORMAT
select output format (or set back to default)
-F, --flags=FLAG[,FLAG...] set interface flags
-i, --interface=NAME
configure network interface NAME
-m, --netmask=MASK
set netmask to MASK
--metric=N
set metric of interface to N
-M, --mtu=N
set mtu of interface to N
-s, --short
short output format
--up activate the interface (default if address is given)
-v, --verbose
output information when configuring interface
Linux-specific options
-T, --txqlen=N
set transmit queue length to N
-?, --help
give this help list
--usage
give a short usage message
-V, --version
print program version
Mandatory or optional arguments to long options are also mandatory or optional for any corresponding short options.
Known flags are: allmulti, automedia, debug, loopback, multicast, portsel, running, trailers, up
AUTHOR
Written by Marcus Brinkmann.
REPORTING BUGS
Report bugs to <bug-inetutils@gnu.org>.
COPYRIGHT
Copyright (C) 2011 Free Software Foundation, Inc. License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>.
This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law.
SEE ALSO
The full documentation for ifconfig is maintained as a Texinfo manual. If the info and ifconfig programs are properly installed at your
site, the command
info ifconfig
should give you access to the complete manual.
GNU inetutils 1.9 December 2011 IFCONFIG(1)