12-18-2008
no such interface
Hi Community,
I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output:
# ifconfig hme0 <ip_address> netmask <mask> plumb
#ifconfig: plumb: hme0: no such interface
I've the same thing with dhcp service.
could you provide any solution please? it is very urgent
Thank you for your availability
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Solaris
Dear ALL,
my server give me messages like below:
Apr 20 21:33:09 TAISERVER in.routed: interface bge3 to 192.168.11.22 turned off
I check with ifconfig,but nothing error that,how can make it solve...thanks for your help. (7 Replies)
Discussion started by: fredginting
7 Replies
3. IP Networking
Hi,
ifconfig -a return:
eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A
inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0
... (5 Replies)
Discussion started by: djbuly
5 Replies
4. UNIX for Advanced & Expert Users
hi all,
i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies
5. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
8. UNIX for Dummies Questions & Answers
Hi All,
How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT NETBSD
ifconfig.if
IFCONFIG.IF(5) BSD File Formats Manual IFCONFIG.IF(5)
NAME
ifconfig.if -- interface-specific configuration files or variables
DESCRIPTION
The ifconfig.if files or variables contain information regarding the configuration of each network interface. ifconfig.if is processed by
/etc/rc.d/network at system boot time.
For each interface (nnX) that is to be configured, there should be either an ifconfig_nnX variable in rc.conf(5), or an /etc/ifconfig.nnX
file (such as the ifconfig_fxp0 variable or the /etc/ifconfig.fxp0 file for the fxp0 interface). Only characters allowed in sh(1) variables
names should be used for nnX (ascii(7) uppercase and lowercase letters, digits, and underscore).
The variable or file will get evaluated only if the interface exists on the system. Multiple lines can be placed in a variable or file, and
will be evaluated sequentially. In the case of a variable, semicolons may be used instead of newlines, as described in rc.conf(5).
<backslash><newline> sequences in files are ignored, so long logical lines may be made up of several shorter physical lines.
Normally, a line will be evaluated as command line arguments to ifconfig(8). ``ifconfig nnX'' will be prepended on evaluation. Arguments
with embedded shell metacharacters should be quoted in sh(1) style.
If the line is equal to ``dhcp'', dhcpcd(8) will be started for the interface. However, it is instead recommended that dhcpcd is set to true
in rc.conf(5) and any per interface configuration or restriction is done in dhcpcd.conf(5).
If a line is empty, or starts with '#', the line will be ignored as comment.
If a line starts with '!', the rest of line will get evaluated as shell script fragment. Shell variables declared in /etc/rc.d/network are
accessible but may not be modified. The most useful variable is $int, as it will be bound to the interface being configured with the file.
For example, the following illustrates static interface configuration:
# IPv4, with an alias
inet 10.0.1.12 netmask 255.255.255.0 media 100baseTX
inet 10.0.1.13 netmask 255.255.255.255 alias
# let us have IPv6 address on this interface
inet6 2001:db8::1 prefixlen 64 alias
# have subnet router anycast address too
inet6 2001:db8:: prefixlen 64 alias anycast
The following illustrates dynamic configuration setup with dhclient(8) and rtsol(8):
up
# autoconfigure IPv4 address
!dhclient $int
# autoconfigure IPv6 address. Be sure to set $ip6mode to autohost.
!rtsol $int
The following example sets a network name for a wireless interface (using quotes to protect special characters in the name), and starts
dhcpcd(8):
ssid 'my network'
dhcp
The following example is for dynamically-created pseudo interfaces like gif(4). Earlier versions of /etc/rc.d/network required an explicit
'create' command for such interfaces, but creation is now handled automatically.
up
# configure IPv6 default route toward the interface
!route add -inet6 default ::1
!route change -inet6 default -ifp $int
FILES
/etc/rc.d/network
SEE ALSO
rc.conf(5), ifconfig(8)
BSD
April 7, 2011 BSD