disk partitioning Post: 302268576

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Partitioning HD

I would like to install Redhat 7.2 on my Windows machine. I only have one hard drive and I dont want to lose Windows. Which method is best for partitioning the HD? I tried it once with Partition Magic and I was installing Corel Linux First Edition and Corel wiped out my entire HD (not good when...

2. UNIX for Dummies Questions & Answers

Hard Disk partitioning to use UNIX

Hello, To run UNIX, can the hard disk be partitioned so I could use that part for UNIX and the other for my existing Windows '98? At the moment there are hard drives C: & D:. Also, where can I obtain the UNIX software?.....Your response is appreciated.

3. UNIX for Advanced & Expert Users

Help: Sun Disk partitioning for Sun V240 & StorEdge 3300

Dear Sun gurus, I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document...

4. Shell Programming and Scripting

Partitioning script for rescue mode (disk size calculation)

Hello! I need to write partitioning script wich would work in rescue mode. It will prepare partitions and unpack linux on it. However I need to calculate whole size of the disk and create: /dev/sda1 --> One big partition (minus (2*size of memory) for swap) /dev/sda2 --> Swap partition...

5. Solaris

Partitioning hard disk. Want 8 slices...have 9

Hi all I'm having difficulty setting up a proper disk structure on a 72GB HDD. The drive was previously part of a zfs pool. The zpool has ben destroyed and now I want to use the disk in a raid 5 array. I need to partition the disk accordingly though. This is what the partition table currently...

6. Red Hat

Disk partitioning commands for RHEL5

I'm new to Linux 5, going through initial phases of installation and setting up devices, etc,, and much to my surprise discovered also an existence of a 2nd hard drive to try to initialize and partition perhaps using any built-in command i.e. "fdisk" or similar, but I couldn't get the command to...

7. Ubuntu

About partitioning

Hi folks, Ubuntu 10.04-1 64-bit HD - 1T SATA3 I ran graphic installation installing Ubuntu-10.04-1 desktop from Live CD The partition on the new HD is as follow; /root /home /kvm (kvm is for keeping the guests of KVM, the virtualizer) Installion went through without problem abd...

8. Red Hat

Partitioning newly added disk to Redhat

Hi Everyone, I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out...

9. UNIX for Dummies Questions & Answers

Which is a recommended method of partitioning Disk?

I m not sure if this is a right question to ask . During the installation of the OS, installation sw does partitioning for you. I m not quit sure if they have used parted or fdisk to partition the disk. (If they are using fdisk then you can't make partition > 2Tb )correct me if i m wrong.Also...

LEARN ABOUT V7

lvscan

LVSCAN(8)						      System Manager's Manual							 LVSCAN(8)

NAME

       lvscan - scan (all disks) for Logical Volumes

SYNOPSIS

       lvscan [-a|--all] [-b|--blockdevice] [-d|--debug] [-h|--help] [--ignorelockingfailure] [-P|--partial] [-v|--verbose]

DESCRIPTION

       lvscan  scans all known volume groups or all supported LVM block devices in the system for defined Logical Volumes.  The output consists of
       one line for each Logical Volume indicating whether or not it is active, a snapshot or origin, the size of the device  and  its	allocation
       policy.	Use lvs(8) or lvdisplay(8) to obtain more-comprehensive information about the Logical Volumes.

OPTIONS

       See lvm for common options.

       --all  Include information in the output about internal Logical Volumes that are components of normally-accessible Logical Volumes, such as
	      mirrors, but which are not independently accessible (e.g. not mountable).  For example, after creating a mirror using 'lvcreate  -m1
	      --mirrorlog disk', this option will reveal three internal Logical Volumes, with suffixes mimage_0, mimage_1, and mlog.

       -b, --blockdevice
	      This option is now ignored.  Instead, use lvs(8) or lvdisplay(8) to obtain the device number.

SEE ALSO

       lvm(8), lvcreate(8), lvdisplay(8) lvs(8)

Sistina Software UK					 LVM TOOLS 2.02.95(2) (2012-03-06)						 LVSCAN(8)