12-15-2008
port access to site to site VPN
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as
https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host 10.0.0.0 host 192.0.0.0
tried adding this
permit tcp host 10.0.0.3 host 192.0.0.5
but nothing
so they should be able to access???
![Confused Smilie](https://www.unix.com/images/smilies/confused.gif)
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello every one,
I have a little issue that has been killing me now for the past couple of days, I have tried to find solutions online, but its been hard to, ok here it goes...
I have created a site that is based on amount of user that have access at a time, based on cookie. So if the browser... (1 Reply)
Discussion started by: heman007
1 Replies
2. UNIX for Advanced & Expert Users
Can someone please give me the conf file line to allow access to myexample.com and only that site, and only through http and https?
So far I have only that site accessible via http, but all https sites are opened.
Squid 3.1 on Cent 6
---------- Post updated at 12:06 PM ---------- Previous... (0 Replies)
Discussion started by: glev2005
0 Replies
3. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
4. Red Hat
Dear All
We have one Centos Server on Asterisk platform.We are trying to open one particular site from client machines which is our client portal.We have to upload data on that.When we trying to open that site somewhere its blocking and not opening.We did tracert and found one router down... (3 Replies)
Discussion started by: Vaibhav.T
3 Replies
5. IP Networking
Guys,
Can I use an open RDP port to gain ssh access to my Linux server running the other side of our firewall?
I work from home on the odd occasion, we only have RDP port 3389 available once logged into the VPN. I would rather ssh into my workstation without the need for a desktop display.
... (3 Replies)
Discussion started by: general_lee
3 Replies
6. IP Networking
Hi all
I need help with a set of iptables rules that would allow a portion of a bank of ipaddresses acces to only one or two named wbsites.
Please advise
Thank You
Ed (3 Replies)
Discussion started by: wa1ed
3 Replies
7. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
8. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
9. Post Here to Contact Site Administrators and Moderators
Hello MODs/Admins,
Could you please help me here as from last 6 to 7 days I(and checked with my fellow friends too) am not able to access unix.com site at all. It is very very slow, it never loads completely. Even I checked with different people and different computers it results same only,... (8 Replies)
Discussion started by: RavinderSingh13
8 Replies
OUTB(2) Linux Programmer's Manual OUTB(2)
NAME
outb, outw, outl, outsb, outsw, outsl, inb, inw, inl, insb, insw, insl, outb_p, outw_p, outl_p, inb_p, inw_p, inl_p - port I/O
DESCRIPTION
This family of functions is used to do low-level port input and output. The out* functions do port output, the in* functions do port
input; the b-suffix functions are byte-width and the w-suffix functions word-width; the _p-suffix functions pause until the I/O completes.
They are primarily designed for internal kernel use, but can be used from user space.
You compile with -O or -O2 or similar. The functions are defined as inline macros, and will not be substituted in without optimization
enabled, causing unresolved references at link time.
You use ioperm(2) or alternatively iopl(2) to tell the kernel to allow the user space application to access the I/O ports in question.
Failure to do this will cause the application to receive a segmentation fault.
CONFORMING TO
outb() and friends are hardware-specific. The value argument is passed first and the port argument is passed second, which is the opposite
order from most DOS implementations.
SEE ALSO
ioperm(2), iopl(2)
COLOPHON
This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1995-11-29 OUTB(2)