Sponsored Content
Operating Systems Linux Red Hat finding no of core in processor Post 302267446 by Autocross.US on Friday 12th of December 2008 10:41:06 AM
Old 12-12-2008
cat /proc/cpuinfo works on RHEL.
 

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

finding out processor speeds for a sparc

i recently purchased a dual ross sparc processor kit from someone. the person listed these items as 133mhz processors, however, looking at bridgepoint's site, they do not make 133mhz processors. so i was wondering, how can i check the processor speeds? (4 Replies)
Discussion started by: xyyz
4 Replies

2. AIX

LPAR processor/virtual processor settings

Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities. Environment is a 8-way p570 with 4 LPARs. lparVIO1 and lparVIO2: AIX 5300-04-01 Mode/Type= Shared-SMT/Capped Minimum Processors= 0.10 Desired Processors= 0.50 Maximum... (1 Reply)
Discussion started by: guttew
1 Replies

3. Linux

linux for dual core processor

hi all I bought a new MSI motherboard and intel dual core processor . i have currently installed fedora core 3 for which audio is not detected . can u tell me which version of fedora core will support as i have tried with fedora core 6 which gets installed but gives a error while... (0 Replies)
Discussion started by: nageshrk
0 Replies

4. UNIX for Dummies Questions & Answers

difference between Dual-core & Core-to-duo

Can anybody tell What is the exact difference between a Dual-core processor and a Core-to-duo processor ?Advance thanks to all my friends. (1 Reply)
Discussion started by: Ajith kumar.G
1 Replies

5. AIX

Processor and processor core

Guys... Hows it going??? I have been going through the hardware spec of IBM system p systems.. and here i am confused for IBM Power 520 Express it says Processor cores: One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration ... (1 Reply)
Discussion started by: balaji_prk
1 Replies

6. Linux

finding core information in redhat Linux

Hi, I want to know how to find out no of cores in linux. I have given the command more /proc/cpuinfo NOw I want to know what is diffrence between cpu cores and core id? How to find out exact no of cores? Regards, Manoj (1 Reply)
Discussion started by: manoj.solaris
1 Replies

7. Linux Benchmarks

AMD Phenom(tm) 9950 Quad-Core Processor, Ram: 3.6 GB, Foxconn 7da-s and Linux 2.6.26-2-amd64

CPU/Speed: AMD Phenom(tm) 9950 Quad-Core Processor Ram: 3.6 GB Motherboard: Foxconn 7da-s Bus: Cache: Controller: Disk: Load: Kernel: Linux 2.6.26-2-amd64 Kernel ELF?: pgms: ============================================================== BYTE UNIX Benchmarks (Version... (0 Replies)
Discussion started by: migracho
0 Replies

8. HP-UX

how can i know this processor quad or dual core ?

hi every body i want to know if i have server with hp-ux os if i did "machinfo" i will see no of cpu = for example 16 how can i know this is dual or quad core . thanks (2 Replies)
Discussion started by: maxim42
2 Replies
CPUID(4)						     Linux Programmer's Manual							  CPUID(4)

NAME
cpuid - x86 CPUID access device DESCRIPTION
CPUID provides an interface for querying information about the x86 CPU. This device is accessed by lseek(2) or pread(2) to the appropriate CPUID level and reading in chunks of 16 bytes. A larger read size means multiple reads of consecutive levels. The lower 32 bits of the file position is used as the incoming %eax, and the upper 32 bits of the file position as the incoming %ecx, the latter intended for "counting" eax levels like eax=4. This driver uses /dev/cpu/CPUNUM/cpuid, where CPUNUM is the minor number, and on an SMP box will direct the access to CPU CPUNUM as listed in /proc/cpuinfo. This file is protected so that it can be read only by the user root, or members of the group root. NOTES
The CPUID instruction can be directly executed by a program using inline assembler. However this device allows convenient access to all CPUs without changing process affinity. Most of the information in cpuid is reported by the kernel in cooked form either in /proc/cpuinfo or through subdirectories in /sys/devices/system/cpu. Direct CPUID access through this device should only be used in exceptional cases. The cpuid driver is not auto-loaded. On modular kernels you might need to use the following command to load it explicitly before use: $ modprobe cpuid There is no support for CPUID functions that require additional input registers. Very old x86 CPUs don't support CPUID. SEE ALSO
Intel Corporation, Intel 64 and IA-32 Architectures Software Developer's Manual Volume 2A: Instruction Set Reference, A-M, 3-180 CPUID ref- erence. Intel Corporation, Intel Processor Identification and the CPUID Instruction, Application note 485. COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 2009-03-31 CPUID(4)
All times are GMT -4. The time now is 11:32 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy