Sponsored Content
Full Discussion: Jumpstart Issues Solaris 10
Operating Systems Solaris Jumpstart Issues Solaris 10 Post 302265075 by DukeNuke2 on Friday 5th of December 2008 02:06:13 PM
Old 12-05-2008
have you run the script "add_install_client" to setup /etc/bootparams file?
 

9 More Discussions You Might Find Interesting

1. Solaris

jumpstart Solaris 10 on Solaris 9 server

I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Discussion started by: salty
5 Replies

2. Solaris

Jumpstart solaris

Hi all , I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows : cleaning up preexisting install client "XXXXXXX" removing XXXXXXXfrom bootparams removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies

3. Solaris

Jumpstart Issues

Hi all, I'm having an issue with jumpstart that I haven't seen before. After booting the server and selecting F12 to boot it from the network it finds the jumpstart profile that has been set up for it and proceeds with the build until I get the following error: SunOS Release 5.10 Version... (4 Replies)
Discussion started by: Chains
4 Replies

4. Solaris

Jumpstart issues, help please.

1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc and jumpstart Server being ultra 20 AMD system. 2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file: 3.When I issued the boot... (7 Replies)
Discussion started by: saagar
7 Replies

5. Solaris

Jumpstart Solaris 10

Hello everyone, I tried to install solaris 10 using the command # boot net - install. I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following: ... (7 Replies)
Discussion started by: yflores
7 Replies

6. Solaris

Issue after jumpstart with Solaris 10 u7

I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created: install_type initial_install system_type server cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies

7. Solaris

Jumpstart Issues With T5220

I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4). The Facts: V210 - Solaris 10 (September 2010 Release / not patched) T5220's - Archive's created using prior (unknown) version of solaris 10. Flar -i <archive name> shows the... (6 Replies)
Discussion started by: Celtic_Monkey
6 Replies

8. Solaris

Jumpstart Solaris 10

I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems. Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86? Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies

9. Solaris

Solaris 10 JumpStart Server

Hello, Can anyone share a good online article/tutorial on how to properly set up JumpStart server for Solaris 10? Thanks, Regards. (3 Replies)
Discussion started by: NewSolarisSquad
3 Replies
rpc.bootparamd(1M)					  System Administration Commands					rpc.bootparamd(1M)

NAME
rpc.bootparamd, bootparamd - boot parameter server SYNOPSIS
/usr/sbin/rpc.bootparamd [-d] DESCRIPTION
rpc.bootparamd is a server process that provides information from a bootparams database to diskless clients at boot time. See bootparams(4) The source for the bootparams database is determined by the nsswitch.conf(4) file (on the machine running the rpc.bootparamd process). OPTIONS
The following options are supported: -d Display debugging information. FILES
/etc/bootparams boot parameter data base /etc/nsswitch.conf configuration file for the name-service switch ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWbsu | +-----------------------------+-----------------------------+ SEE ALSO
svcs(1),svcadm(1M), bootparams(4), nsswitch.conf(4), attributes(5), smf(5) NOTES
A diskless client requires service from at least one rpc.bootparamd process running on a server that is on the same IP subnetwork as the diskless client. Some routines that compare hostnames use case-sensitive string comparisons; some do not. If an incoming request fails, verify that the case of the hostname in the file to be parsed matches the case of the hostname called for, and attempt the request again. The rpc.bootparamd service is managed by the service management facility, smf(5), under the service identifier: svc:/network/rpc/bootparams Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using svcadm(1M). The ser- vice's status can be queried using the svcs(1) command. SunOS 5.10 1 Aug 2004 rpc.bootparamd(1M)
All times are GMT -4. The time now is 10:48 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy