12-04-2008
how to get CPU name
The better option to go with for you would be,
#man lanscan
#man lanadmin
#man netstat
I think
-DB
Last edited by DustBunny; 12-04-2008 at 05:02 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT DEBIAN
io::all::http
IO::All::HTTP(3pm) User Contributed Perl Documentation IO::All::HTTP(3pm)
NAME
IO::All::LWP - Extends IO::All to HTTP URLs
SYNOPSIS
use IO::All;
$content < io('http://example.org'); # GET webpage into scalar
io('http://example.org') > io('index.html'); # GET to file
"hello
" > io('http://example.org/index.html'); # PUT webpage
# two ways of getting a page with a password:
$content < io('http://me:secret@example.org');
$content < io('http://example.org')->user('me')->password('secret');
DESCRIPTION
This module extends IO::All for dealing with HTTP URLs. Note that you don't need to use it explicitly, as it is autoloaded by IO::All
whenever it sees something that looks like an HTTP URL.
The SYNOPSIS shows some simple typical examples, but there are many other interesting combinations with other IO::All features! For
example, you can get an HTTP URL and write the content to a socket, or to an FTP URL, of to a DBM file.
METHODS
This is a subclass of IO::All::LWP. The only new method is "http", which can be used to create a blank IO::All::HTTP object; or it can also
take an HTTP URL as a parameter. Note that in most cases it is simpler just to call io('http://example.com'), which calls the "http" method
automatically.
OPERATOR OVERLOADING
The same operators from IO::All may be used. < GETs an HTTP URL; > PUTs to an HTTP URL.
SEE ALSO
IO::All, IO::All::LWP, LWP.
AUTHORS
Ivan Tubert-Brohman <itub@cpan.org> and Brian Ingerson <ingy@cpan.org>
COPYRIGHT
Copyright (c) 2007. Ivan Tubert-Brohman and Brian Ingerson. All rights reserved.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
See <http://www.perl.com/perl/misc/Artistic.html>
perl v5.10.0 2007-03-29 IO::All::HTTP(3pm)