12-04-2008
how to get CPU name
The better option to go with for you would be,
#man lanscan
#man lanadmin
#man netstat
I think
-DB
Last edited by DustBunny; 12-04-2008 at 05:02 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT SUSE
dacs_version
DACS_VERSION(8) DACS Web Services Manual DACS_VERSION(8)
NAME
dacs_version - display DACS version information
SYNOPSIS
dacs_version [dacsoptions[1]]
DESCRIPTION
This program is part of the DACS suite.
The dacs_version web service displays version information about DACS and other third-party packages that have been compiled into DACS. If
XML output is selected, a document conforming to dacs_version.dtd[2] is returned.
Note
This program is also available as a DACS utility, dacsversion(1)[3]. Because dacs_admin(8)[4] provides the same functionality and more,
dacs_version may be removed in a future release.
OPTIONS
Web Service Arguments
The standard CGI arguments[5] are understood.
DIAGNOSTICS
The program exits 0 if everything was fine, 1 if an error occurred.
SEE ALSO
dacs(1)[6]
AUTHOR
Distributed Systems Software (www.dss.ca[7])
COPYING
Copyright2003-2012 Distributed Systems Software. See the LICENSE[8] file that accompanies the distribution for licensing information.
NOTES
1. dacsoptions
http://dacs.dss.ca/man/dacs.1.html#dacsoptions
2. dacs_version.dtd
http://dacs.dss.ca/man/../dtd-xsd/dacs_version.dtd
3. dacsversion(1)
http://dacs.dss.ca/man/dacsversion.1.html
4. dacs_admin(8)
http://dacs.dss.ca/man/dacs_admin.8.html
5. standard CGI arguments
http://dacs.dss.ca/man/dacs.services.8.html#standard_cgi_args
6. dacs(1)
http://dacs.dss.ca/man/dacs.1.html
7. www.dss.ca
http://www.dss.ca
8. LICENSE
http://dacs.dss.ca/man/../misc/LICENSE
DACS 1.4.27b 10/22/2012 DACS_VERSION(8)