Hi All
I've used UNIX in the past experimenting with commands through terminal but thats about it. Im now currently teaching myself "C".
Using a book from the library, the first chapter asks you run and compile your program from a command-line prompt. As you will see the program is very simple,... (4 Replies)
Hi,
I want to split before reading the complete line as the line is very big and its throwing out of memory. can you suggest.
when i say
#cat $inputFile | while read eachLine
and use the eachLine to split its throwing out of memory as the line size is more than 10000000 characters.
Can you... (1 Reply)
Dear All,
I want to split single line into two line or three lines wherever “|” separated values comes using
Input line
test,DEMTEMPUT20100404010012,,,,,,,,|0070086|0070087,
output shoule be
test,DEMTEMPUT20100404010012,,,,,,,,0070086,
test,DEMTEMPUT20100404010012,,,,,,,,0070087, (14 Replies)
I guess this has a simple solution but can't figure out now.
having:
x="H:a:b:c"
to get H:
echo $x|awk -F: {'print $1'}
how can I put REST of line in another one? i.e.
echo $rest
a:b:c
thanks
---------- Post updated at 08:58 PM ---------- Previous update was at... (5 Replies)
first of all I thought the argument DONE is necessary for all scripts that have or begin with do statements which I have on my script, However, I still don't completely understand why I am receiving an error I tried adding another done argument statement but didn't do any good.
I appreciate... (3 Replies)
Hello.
The token is any printable characters between 2 " .
The token is unknown, but we know that it is between 2 "
Tok 1 : "1234x567"
Tok 2 : "A3b6+None"
Tok 3 : "A3b6!1234=@"
The ligne is :
Line 1 :
"9876xABCDE"Do you have any code fragments or data samples in your post
Line 2 : ... (3 Replies)
Hello.
I have a config file (/etc/my_config_file) which may content :
#
# port for HTTP (descriptions, SOAP, media transfer) traffic
port=8200
# network interfaces to serve, comma delimited
network_interface=eth0
# set this to the directory you want scanned.
# * if have multiple... (6 Replies)
Hi All,
Hope you guys had a wonderful weekend
I have a scenario where in which I have to read a file line by line
and check for few words before redirecting to a file
I have searched the forum but,either those answers dint work (perhaps because of my wrong under standing of how IFS... (6 Replies)
I have a very long line in a file separated by "|" delimiter like below. Due to the length of the line, I find it very difficult to read to find a match line.
file = temp.txt
word 1| word 2 | word 3|....
I would like to read the file temp.txt and print out all words line by line like... (1 Reply)
Below query is not working for me. Please help me on this
DATA EXCLUDE STATEMENT: TABLE:\"LIKE \'%\_HISTORY\'\", TABLE:\"LIKE \'%\_HIST\'\", TABLE:\"in \(select tname from tab where REGEXP_LIKE(TNAME,\'\_H$\'\))\", TABLE:\"LIKE \'%\_LOG\'\", TABLE:\"LIKE \'DW\_%\'\", TABLE:\"LIKE... (1 Reply)
Discussion started by: princy
1 Replies
LEARN ABOUT OPENSOLARIS
split
split(1) User Commands split(1)NAME
split - split a file into pieces
SYNOPSIS
split [-linecount | -l linecount] [-a suffixlength]
[file [name]]
split [-b n | nk | nm] [-a suffixlength] [file [name]]
DESCRIPTION
The split utility reads file and writes it in linecount-line pieces into a set of output-files. The name of the first output-file is name
with aa appended, and so on lexicographically, up to zz (a maximum of 676 files). The maximum length of name is 2 characters less than the
maximum filename length allowed by the filesystem. See statvfs(2). If no output name is given, x is used as the default (output-files will
be called xaa, xab, and so forth).
OPTIONS
The following options are supported:
-linecount | -l linecount
Number of lines in each piece. Defaults to 1000 lines.
-a suffixlength
Uses suffixlength letters to form the suffix portion of the filenames of the split file. If -a is not specified, the default suffix
length is 2. If the sum of the name operand and the suffixlength option-argument would create a filename exceeding NAME_MAX bytes, an
error will result; split will exit with a diagnostic message and no files will be created.
-b n
Splits a file into pieces n bytes in size.
-b nk
Splits a file into pieces n*1024 bytes in size.
-b nm
Splits a file into pieces n*1048576 bytes in size.
OPERANDS
The following operands are supported:
file The path name of the ordinary file to be split. If no input file is given or file is -, the standard input will be used.
name The prefix to be used for each of the files resulting from the split operation. If no name argument is given, x will be used as the
prefix of the output files. The combined length of the basename of prefix and suffixlength cannot exceed NAME_MAX bytes. See
OPTIONS.
USAGE
See largefile(5) for the description of the behavior of split when encountering files greater than or equal to 2 Gbyte ( 2^31 bytes).
ENVIRONMENT VARIABLES
See environ(5) for descriptions of the following environment variables that affect the execution of split: LANG, LC_ALL, LC_CTYPE, LC_MES-
SAGES, and NLSPATH.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
>0 An error occurred.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWesu |
+-----------------------------+-----------------------------+
|CSI |Enabled |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
|Standard |See standards(5). |
+-----------------------------+-----------------------------+
SEE ALSO csplit(1), statvfs(2), attributes(5), environ(5), largefile(5), standards(5)SunOS 5.11 16 Apr 1999 split(1)