11-26-2008
It really depends on what you have and/or what you need. Both work fine.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi. I have installed Solaris 8 and I am trying to configure the network settings. For some reason every time I reboot, my card loses its configuration. I can run ifconfig and the only IP address bound to my card (on either interface) is 127.0.0.1. I can change that to a valid IP address on my... (8 Replies)
Discussion started by: Ask Me
8 Replies
2. IP Networking
Hi,
I need to configure the Network for a Sun Solaris systems.
The OS info is SunOS Sparsh 5.8 Generic_108528-13 Sun4u Sparc SUNW,Ultra-250.
Please do let me know, how shall I shart with & more in configuring the Network.
Below is the list of Network Configuration I need to Make
... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies
3. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
4. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
5. Solaris
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies
6. UNIX for Dummies Questions & Answers
I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine.
Also, if there is any short tutorials on using the commands, i would defiently like that information.
Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies
7. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
8. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
9. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
10. UNIX for Advanced & Expert Users
Hi all,
I got following configuration problem
I need to configure tiny network on openbsd
I got server1 with 3 interfaces vic0 em0 em1
The interface vic0 on server1 has follwoing IP 172.16.1.1
em0
firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
PSIZE(1) PDB2PQR Manual PSIZE(1)
NAME
psize - Get dimensions and other information from PQR files
SYNOPSIS
psize [--cfact=value] [--fadd=value] [--space=value] [--gememfac=value] [--gememceil=value] [--ofrac=value] [--redfac=value] {pqrfile}
psize {--help | -h}
DESCRIPTION
psize derives information from PQR files to preprare the models of proteins and chemicals for electrostatics calculations. The tool
calculates dimensions for coarse and fine grids, grid spacings, box size and estimates the memory required to perform an electrostatics
calculation.
The calculation of this information can be influenced by giving constraints to psize as parameters.
OPTIONS
psize accepts the following options:
--help, -h
Print a help message and exit.
--cfact=value
Factor by which to expand the molecule dimensions to get the coarse grid dimensions
--fadd=value
Amount to add to the molecule dimensions to get the fine grid dimensions.
--space=value
Desired fine mesh resolution.
--gememfac=value
Number of bytes per grid point required for sequential MG calculation.
--gememceil=value
Maximum MB allowed for sequential MG calculation. Adjust this to force the script to perform faster calculations (which require more
parallelism).
--ofrac=value
Overlap factor between mesh partitions.
--redfac=value
Maximum factor by which a domain dimension can be reduced during focusing.
SEE ALSO
apbs(1), pdb2pqr(1)
AUTHOR
Manuel Prinz <debian@pinguinkiste.de>
Wrote this manpage for the Debian System.
COPYRIGHT
Copyright (C) 2008 Manuel Prinz
psize 2008-06-04 PSIZE(1)