Sponsored Content
Top Forums Shell Programming and Scripting network and broadcast address Post 302256290 by scofiled83 on Sunday 9th of November 2008 07:42:20 AM
Old 11-09-2008
thanks for the answer, Could u explain a little bit more, how did u come up to that solution
 

10 More Discussions You Might Find Interesting

1. IP Networking

broadcast address

What is the significance of the broadcast address? (1 Reply)
Discussion started by: 98_1LE
1 Replies

2. UNIX for Dummies Questions & Answers

network address and broadcast address?

say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on? And could you explain how to get the answer? thanx in advance! (7 Replies)
Discussion started by: pnxi
7 Replies

3. Solaris

bge card and broadcast address

I have a bge1 card and a bge0 card, i want the broadcast addresses to match, ifconfig shows this lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 ... (1 Reply)
Discussion started by: csaunders
1 Replies

4. AIX

NETWORK IP ADDRESS on HACMP

Hi, I try to understand how to configure my ethernet network in a hacmp cluster. I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster. I don't have any serial o iscsi heartbeat. Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies

5. IP Networking

Obtaining IP address from both my network interface

HI folks, I am developing a software which one of the module is to interchange the ip address of another active network interface's when making a socket connection. I would like to know whether there is any function call that would enable me to retrieve the ip address that is obtained by a... (2 Replies)
Discussion started by: citiz3n
2 Replies

6. Solaris

ifconfig - making netmask & broadcast address permanent?

hi, I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address. I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated. before reboot: eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies

7. Programming

How to broadcast a message across the network using Socket programming in C??

My problem definition is ,I have to send a message from one node in a network and it has to be broadcasted to all other nodes in the network.The program what I have given below will be running in all the nodes in the network.The same program should be capable of sending(broadcasting) and receiving.... (1 Reply)
Discussion started by: vigneshinbox
1 Replies

8. UNIX for Dummies Questions & Answers

fake network address....

Good morning! Why would having a fake network device be useful? Thanks in advance Bigben (0 Replies)
Discussion started by: bigben1220
0 Replies

9. Shell Programming and Scripting

Shell script to give broadcast and network address

Hello, I am running a post script in autoyast where I am trying to set the broadcast and network address. I have the ip address and netmask already (reading from a file).. I saw the post from fpmurphy but it is using ksh which isn't an option in autoyast. Thanks in advance! (3 Replies)
Discussion started by: bloodclot
3 Replies

10. IP Networking

Network address translation

How would one approach the problem of determining the NAT tables of a router without knowing the userid and password. The only password holder died. I know the internal ip address of the router is 192.168.2.1, and also ports 80 or 8080 and 3389 are open. (5 Replies)
Discussion started by: jgt
5 Replies
MRTG-FORUM(1)							       mrtg							     MRTG-FORUM(1)

NAME
mrtg-forum - Interactive Help for MRTG users SYNOPSIS
There is a lot of written documentation for mrtg, but nevertheless you may have a problem where you can't find the solution. In this case some Human Help may be necessary. With MRTG there are several ways to get Humans to help you. MAILING-LIST There are three mailing lists for MRTG available. mrtg for discussion among mrtg users. mrtg-announce for announcements regarding new versions of mrtg related software. mrtg-developers for discussion among people who write software in connection with mrtg or who hack mrtg itself. THE RULES Please note that the memebers of the mrtg mailinglist value politeness highly. This means behave in a way you would like others to behave towards you. o No shouting. (NO CAPS) o No rude language o No demands. everybody is on the list out of their own free will. If you do not get an answer to your question, chances are high that you did not give sufficent details about the nature of your problem or that the answer to your problem is in the documentation. o If you do not follow the rules you will be unsubscribed from the list with no further questions asked. o Decisions about your unsubscription from the list will be taken by Alex van den Bogaerdt <alex at ergens.op.het.net> Paul C. Williamson <pwilliamson at MANDTBANK.COM> If you feel that you have been treated unfairly, you may send mail to me and explain the situation. Tobi Oetiker <tobi@oetiker.ch> SUBSCRIBING These lists are managed by a mailing-list management program (listar). It allows you to subscribe to these lists by sending a message with the subject: subscribe to the following address: listname-request@lists.oetiker.ch You will then get a message asking you to confirm your subscription. For posting to the lists use the following address listname@lists.oetiker.ch Note that only people who are subscribed to the list can post. Further information about the usage of the mailing lists is available by sending a message with the subject line help to either one of the request addresses. There is also a webinterface to the lists on http://lists.oetiker.ch List archives are on http://www.mail-archive.com/index.php?hunt=mrtg and http://gmane.org/find.php?list=mrtg NEWSGROUP
For discussion of MRTG or related topics on the Usenet, please send your posts to: news:comp.dcom.net-management Many MRTG users are in this forum and will help you. You can also find an archive of past activity from this Newsgroup on: http://groups.google.com/group/comp.dcom.net-management IRC Channel For discussion of MRTG and related topics on IRC, the `#mrtg' channel on EFNet has been created. More information can be found at http://mrtg.easymac.org MRTG Japan There is a special Mailinglist for MRTG Users in Japan. It carries translations of the traffic from MRTG-ANNOUNCE as well as updates on the Japanese Translation of the MRTG documentation. Go to http://www.mrtg.jp/ for further Information. AUTHOR
Tobias Oetiker <tobi@oetiker.ch> and many contributors 2.17.4 2012-01-12 MRTG-FORUM(1)
All times are GMT -4. The time now is 01:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy