11-09-2008
kenny has a "network" of 192.168.0.0 with a broadcast of 192.168.0.15. The hosts on this subnet range from 192.168.0.1 - 192.168.0.14.
zanthras has a "network" of 192.168.0.16 with a broadcast of 192.168.0.31. The hosts on this subnet range from 192.168.0.17 - 192.168.0.30.
You need that router.
10 More Discussions You Might Find Interesting
1. IP Networking
What is the significance of the broadcast address? (1 Reply)
Discussion started by: 98_1LE
1 Replies
2. UNIX for Dummies Questions & Answers
say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on?
And could you explain how to get the answer?
thanx in advance! (7 Replies)
Discussion started by: pnxi
7 Replies
3. Solaris
I have a bge1 card and a bge0 card, i want the broadcast addresses to match, ifconfig shows this
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
... (1 Reply)
Discussion started by: csaunders
1 Replies
4. AIX
Hi, I try to understand how to configure my ethernet network in a hacmp cluster.
I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster.
I don't have any serial o iscsi heartbeat.
Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies
5. IP Networking
HI folks,
I am developing a software which one of the module is to interchange the ip address of another active network interface's when making a socket connection.
I would like to know whether there is any function call that would enable me to retrieve the ip address that is obtained by a... (2 Replies)
Discussion started by: citiz3n
2 Replies
6. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
7. Programming
My problem definition is ,I have to send a message from one node in a network and it has to be broadcasted to all other nodes in the network.The program what I have given below will be running in all the nodes in the network.The same program should be capable of sending(broadcasting) and receiving.... (1 Reply)
Discussion started by: vigneshinbox
1 Replies
8. UNIX for Dummies Questions & Answers
Good morning!
Why would having a fake network device be useful?
Thanks in advance
Bigben (0 Replies)
Discussion started by: bigben1220
0 Replies
9. Shell Programming and Scripting
Hello,
I am running a post script in autoyast where I am trying to set the broadcast and network address.
I have the ip address and netmask already (reading from a file)..
I saw the post from fpmurphy but it is using ksh which isn't an option in autoyast.
Thanks in advance! (3 Replies)
Discussion started by: bloodclot
3 Replies
10. IP Networking
How would one approach the problem of determining the NAT tables of a router without knowing the userid and password. The only password holder died.
I know the internal ip address of the router is 192.168.2.1, and also ports 80 or 8080 and 3389 are open. (5 Replies)
Discussion started by: jgt
5 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)