11-09-2008
kenny has a "network" of 192.168.0.0 with a broadcast of 192.168.0.15. The hosts on this subnet range from 192.168.0.1 - 192.168.0.14.
zanthras has a "network" of 192.168.0.16 with a broadcast of 192.168.0.31. The hosts on this subnet range from 192.168.0.17 - 192.168.0.30.
You need that router.
10 More Discussions You Might Find Interesting
1. IP Networking
What is the significance of the broadcast address? (1 Reply)
Discussion started by: 98_1LE
1 Replies
2. UNIX for Dummies Questions & Answers
say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on?
And could you explain how to get the answer?
thanx in advance! (7 Replies)
Discussion started by: pnxi
7 Replies
3. Solaris
I have a bge1 card and a bge0 card, i want the broadcast addresses to match, ifconfig shows this
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
... (1 Reply)
Discussion started by: csaunders
1 Replies
4. AIX
Hi, I try to understand how to configure my ethernet network in a hacmp cluster.
I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster.
I don't have any serial o iscsi heartbeat.
Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies
5. IP Networking
HI folks,
I am developing a software which one of the module is to interchange the ip address of another active network interface's when making a socket connection.
I would like to know whether there is any function call that would enable me to retrieve the ip address that is obtained by a... (2 Replies)
Discussion started by: citiz3n
2 Replies
6. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
7. Programming
My problem definition is ,I have to send a message from one node in a network and it has to be broadcasted to all other nodes in the network.The program what I have given below will be running in all the nodes in the network.The same program should be capable of sending(broadcasting) and receiving.... (1 Reply)
Discussion started by: vigneshinbox
1 Replies
8. UNIX for Dummies Questions & Answers
Good morning!
Why would having a fake network device be useful?
Thanks in advance
Bigben (0 Replies)
Discussion started by: bigben1220
0 Replies
9. Shell Programming and Scripting
Hello,
I am running a post script in autoyast where I am trying to set the broadcast and network address.
I have the ip address and netmask already (reading from a file)..
I saw the post from fpmurphy but it is using ksh which isn't an option in autoyast.
Thanks in advance! (3 Replies)
Discussion started by: bloodclot
3 Replies
10. IP Networking
How would one approach the problem of determining the NAT tables of a router without knowing the userid and password. The only password holder died.
I know the internal ip address of the router is 192.168.2.1, and also ports 80 or 8080 and 3389 are open. (5 Replies)
Discussion started by: jgt
5 Replies
LEARN ABOUT MOJAVE
findsmb
FINDSMB(1) User Commands FINDSMB(1)
NAME
findsmb - list info about machines that respond to SMB name queries on a subnet
SYNOPSIS
findsmb [subnet broadcast address]
DESCRIPTION
This perl script is part of the samba(7) suite.
findsmb is a perl script that prints out several pieces of information about machines on a subnet that respond to SMB name query requests.
It uses nmblookup(1) and smbclient(1) to obtain this information.
OPTIONS
-r
Controls whether findsmb takes bugs in Windows95 into account when trying to find a Netbios name registered of the remote machine. This
option is disabled by default because it is specific to Windows 95 and Windows 95 machines only. If set, nmblookup(1) will be called
with -B option.
subnet broadcast address
Without this option, findsmb will probe the subnet of the machine where findsmb(1) is run. This value is passed to nmblookup(1) as part
of the -B option.
EXAMPLES
The output of findsmb lists the following information for all machines that respond to the initial nmblookup for any name: IP address,
NetBIOS name, Workgroup name, operating system, and SMB server version.
There will be a '+' in front of the workgroup name for machines that are local master browsers for that workgroup. There will be an '*' in
front of the workgroup name for machines that are the domain master browser for that workgroup. Machines that are running Windows for
Workgroups, Windows 95 or Windows 98 will not show any information about the operating system or server version.
The command with -r option must be run on a system without nmbd(8) running. If nmbd is running on the system, you will only get the IP
address and the DNS name of the machine. To get proper responses from Windows 95 and Windows 98 machines, the command must be run as root
and with -r option on a machine without nmbd running.
For example, running findsmb without -r option set would yield output similar to the following
IP ADDR NETBIOS NAME WORKGROUP/OS/VERSION
---------------------------------------------------------------------
192.168.35.10 MINESET-TEST1 [DMVENGR]
192.168.35.55 LINUXBOX *[MYGROUP] [Unix] [Samba 2.0.6]
192.168.35.56 HERBNT2 [HERB-NT]
192.168.35.63 GANDALF [MVENGR] [Unix] [Samba 2.0.5a for IRIX]
192.168.35.65 SAUNA [WORKGROUP] [Unix] [Samba 1.9.18p10]
192.168.35.71 FROGSTAR [ENGR] [Unix] [Samba 2.0.0 for IRIX]
192.168.35.78 HERBDHCP1 +[HERB]
192.168.35.88 SCNT2 +[MVENGR] [Windows NT 4.0] [NT LAN Manager 4.0]
192.168.35.93 FROGSTAR-PC [MVENGR] [Windows 5.0] [Windows 2000 LAN Manager]
192.168.35.97 HERBNT1 *[HERB-NT] [Windows NT 4.0] [NT LAN Manager 4.0]
VERSION
This man page is correct for version 3 of the Samba suite.
SEE ALSO
nmbd(8), smbclient(1), and nmblookup(1)
AUTHOR
The original Samba software and related utilities were created by Andrew Tridgell. Samba is now developed by the Samba Team as an Open
Source project similar to the way the Linux kernel is developed.
The original Samba man pages were written by Karl Auer. The man page sources were converted to YODL format (another excellent piece of Open
Source software, available at ftp://ftp.icce.rug.nl/pub/unix/) and updated for the Samba 2.0 release by Jeremy Allison. The conversion to
DocBook for Samba 2.2 was done by Gerald Carter. The conversion to DocBook XML 4.2 for Samba 3.0 was done by Alexander Bokovoy.
Samba 3.5 06/18/2010 FINDSMB(1)