Sponsored Content
Full Discussion: Cause of NIC changes ...?
Operating Systems Solaris Cause of NIC changes ...? Post 302255346 by incredible on Thursday 6th of November 2008 09:34:36 AM
Old 11-06-2008
Quote:
Originally Posted by DukeNuke2
this is no problem. the pci bus is scanned before the internel nics are scanned. so they will become net0 and so on. if you like to have the internal nics to be net0... you have to pull out the additional cards, install the system and then insert the cards again.
Thank you vimes for the info. Smilie
DukeNuke, our practise is to integrate the h/w first then we install the OS. Other systems did not have such issue, only this. But seeing your explanation, it does make sense to follow such procedure.. But for this server, we lack time to do re-installation now..

Thx alot guys! Smilie
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

nic configuration

Hi, what are the basic steps/command to configure a new nic (2nd) on Solaris 9? :eek: 10x N. (4 Replies)
Discussion started by: nadav
4 Replies

2. SCO

Need Help installing NIC

Hi guys, I am a newbie in SCO UNIX, and I am having problem in installing a NIC for my machine: My machine: UnixWare scou 5 7.1.4 i386 x86at SCO UNIX_SVR5 My NIC is dLink DFE-538TX, I got the driver from: http://support.dlink.ca/ProductView.asp?ProductModel=DFE-538TX The driver... (1 Reply)
Discussion started by: Voldi
1 Replies

3. Shell Programming and Scripting

NIC address

how can I know the Network Interface Card physical address? (4 Replies)
Discussion started by: nokia1100
4 Replies

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

5. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

6. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

7. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

8. HP-UX

Configure Second NIC on HP UX?

Hello, I need to configure a second NIC on my HP UX, B.11.31 U ia64 ...if it is helpful. I see a good thread to start on: Configuring NIC https://www.unix.com/hp-ux/15589-configuring-nic.html I have started reading the man pages listed. Without having to know every last detail is there... (3 Replies)
Discussion started by: KmJohnson
3 Replies

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
DUMMY_CS(4)						     Kernel Interfaces Manual						       DUMMY_CS(4)

NAME
dummy_cs - PCMCIA dummy device driver SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...] DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set- ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers. It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions about card types, it is forced to rely on the card information, for better or worse. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. free_ports=n A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5). pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)
All times are GMT -4. The time now is 01:19 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy