10-28-2008
Funny I can see them all except one:
semmap
But if you had read the release notes especially : (release notes 11iv2 oct 2003)
http://docs.hp.com/en/5992-1968/5992-1968.pdf
On page 82 you would have noticed:
Quote:
• System-V IPC Kernel Tunable Parameter (semmap)(Obsolete): The memory allocation of
semaphore sets previously controlled by semmap is now done dynamically by the kernel.
The semmap kernel parameter is no longer tunable.
So before continuing further I would recommend you to look at the man pages of
kctune(1M) kmtune(1M) kclog(1M) kconfig(1M)
And read carefully:
Chapter*10*Configuring the Kernel
Last edited by vbe; 10-28-2008 at 12:05 PM..
Reason: addition: forgot kconfig
10 More Discussions You Might Find Interesting
1. HP-UX
I want to change some kernel parameters in HP-UX11, to do with Oracle upgrade/install.
I know this is done using SAM. I am told SAM will not let you enter values outside the allowable range. Could anyone tell me if they have experienced anything different?
In Solaris, I would copy the... (2 Replies)
Discussion started by: malcqv
2 Replies
2. HP-UX
Hello all, Can anyone tell me the command line I can use to look at the following Kernel parameters:
nfile
maxfile
maxfile_lim
I'm using the Reflection manager connection to my Unix box so I can't use SAM. (3 Replies)
Discussion started by: impunchdrunk
3 Replies
3. UNIX for Advanced & Expert Users
Can only root do this, or can other users too? if other users can, do they have to be given permission, and if so, is there a file or something that stores this?
Thanks. (4 Replies)
Discussion started by: JamesByars
4 Replies
4. HP-UX
I've been trying to find out the following parameters of our Unix box:
==>OS version
==> patch level
and the following kernel parameters
=>maxfiles_lim
=>maxvgs
=>nproc
=>msgmni
=>ncsize
=>nfile
Could someone help me how would I find the above(commands)?
Thanks,
Bhagat (1 Reply)
Discussion started by: bhagat.singh-j
1 Replies
5. Solaris
Hello,
Can anyone point me out as to how to set the following parameters in Solaris Kernel: set semsys:seminfo_semmni=16384, set semsys:seminfo_semmns=32768,set semsys:seminfo_semmsl=1024,
set semsys:seminfo_semmnu=16384,set semsys:seminfo_semume=1024,
set shmsys:shminfo_shmmax=4294967295,set... (8 Replies)
Discussion started by: AQG
8 Replies
6. Solaris
Hi gurus
Could anybody tell me which file is read by kernel to set its default system kernal parameters values in solaris. Here I am not taking about /etc/system file which is used to load kernal modules or to change any default system kernal parameter value
Is it /dev/kmem file or something... (1 Reply)
Discussion started by: girish.batra
1 Replies
7. Linux
Hi,
if I install a module with specific parameter, will this parameters applied next time system boots?
for exampe, I want to disable InterruptThrottleRate
modprobe e1000e InterruptThrottleRate=0
Is this parameter apllied only for this run, or this module will always use this parameter when... (2 Replies)
Discussion started by: Shedon
2 Replies
8. Solaris
Dear All,
I want to check whether all essential kernel parameters are installed in my Solaris 10 System. Is there any way to find it.
And also how to tune it.
Kindly help.
Thanks and Regards
Rj (8 Replies)
Discussion started by: jegaraman
8 Replies
9. Solaris
Dear All,
I have weblogic Portal Installed in the Server solaris 10.
How can i verify whether all the kernel parameters are available for this Software and also another question is
How to crosscheck a server ( Solaris 10 Sparc ) whether it has all the required kernel parameters.
... (2 Replies)
Discussion started by: jegaraman
2 Replies
10. UNIX for Dummies Questions & Answers
Virtual Machine running on VMWare workstation 9.2
os : RHEL 5.8
RAM : 2.5GB
Swap : 2.6gb
CPU : 1 virtual CPU
Surprizingly I couldn't find much from googling on What exactly does Kernel parameters do ?
I was under the impression that kernel parameters just set the limits/maximum for a... (2 Replies)
Discussion started by: John K
2 Replies
LEARN ABOUT HPUX
vx_maxlink
vx_maxlink(5) File Formats Manual vx_maxlink(5)
NAME
vx_maxlink - Configure the number of links to a file
SYNOPSIS
VALUE
Specify an integer value.
Minimum
0
Maximum
65534
Default
32767
DESCRIPTION
The tunable is used to configure the number of links possible to a file on VxFS filesystem
As is initialized when system is booted, the changes made to will take effect only from the next system reboot.
EXAMPLES
Set the maximum number of links to a file at 40000:
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or its meaning may change in the future releases
of HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
SEE ALSO
kctune(1M), vx_ninode(5), vxfs_bc_bufhwm(5), vxfs_ifree_timelag(5).
Tunable Kernel Parameters vx_maxlink(5)