Sponsored Content
Special Forums IP Networking Static IP / Subnet mask and Gateway Post 302251040 by Lazydog on Friday 24th of October 2008 10:08:34 PM
Old 10-24-2008
How did you change your config?
Make sure 'BOOTPROTO=static' is set in the ifcfg-eth0 file.

If that doesn't work post your ifcfg-eth0 file so we can see what might be the problem.
 

9 More Discussions You Might Find Interesting

1. IP Networking

Subnet mask

Hi, I have about 30 computers for users with subnet mask x.x.x.0, and 25 computers for workers with s.m. x.x.x.128. My server has a s.m. x.x.x.128 so with workers computers I can see my server and all the computers in that s.m., but I can't see the server from the users computers and I need to see... (7 Replies)
Discussion started by: Z0DiaC
7 Replies

2. IP Networking

changing the subnet mask permanently

I understand how to change the ip address permanently however, I need to also make a permanent change to the subnet mask. How would I accomplish this. (5 Replies)
Discussion started by: johnparksjr
5 Replies

3. Solaris

Need help in changing the subnet mask

Hi, I have a task to edit the subnet mask in almost 100+ solaris servers.Few of the servers are configured with IPMP.There will be no change of IP address or default gateway.If its a single IP we can bring NIC down,change the subnet mask in /etc/netmasks,then bring the NIC back to normal.But... (3 Replies)
Discussion started by: rajip23
3 Replies

4. Solaris

how to change the subnet mask of interface

Hi all, could you please tell me how to Change the subnet mask of interface aded:1 from ffffffc0 to ffffff80 regards Krishna (7 Replies)
Discussion started by: murthy76
7 Replies

5. AIX

Changing subnet mask for a NIM Network.

I am new to this forum so please bare with me. I did search for this answer prior to posting but no luck. Running an AIX NIM Master at 5.3TL9SP4, with about 100 clients. The subnet of one of the networks defined in the NIM env has changed. When I go to Manage Networks, Change/Show... (0 Replies)
Discussion started by: juredd1
0 Replies

6. Linux

GNUGK-How to setup static gateway to gateway routing

Dear Sir I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper. I am having a problem, configuring static call routing on GNUGK in the section ... (0 Replies)
Discussion started by: mfondoum
0 Replies

7. IP Networking

lookup ip address, subnet mask, gateway, and dns at same time

Is there a command that can lookup ip address, subnet mask, gateway, and dns all at the same. I know ifconfig can lookup ip address and subnet mask. I know route -n can lookup gateway. Not sure about a dns command. So I hope there is a way to lookup ip address, subnet mask, gateway, and dns all at... (2 Replies)
Discussion started by: cokedude
2 Replies

8. Solaris

Changing the subnet mask on solaris 10

Hello, can anyone help me with the command to change the subnet mask on solaris 10? The mask is currently 255.255.255.255 I will like to change it to 255.255.2555.0. Thank you (5 Replies)
Discussion started by: cjashu
5 Replies

9. Shell Programming and Scripting

Get all ip address from subnet mask

I have this subnet file shown below. How can I calculate all ip addresses from that list 103.22.200.0/22 141.101.64.0/18 10.0.0.0/22I need to be able to read the subnet file and print all IPs in those subnet to an out put file (3 Replies)
Discussion started by: e_mikey_2000
3 Replies
ECACCESS-ASSOCIATION-LIST(1p)				User Contributed Perl Documentation			     ECACCESS-ASSOCIATION-LIST(1p)

NAME
ecaccess-association-list - List your ECtrans Associations SYNOPSIS
ecaccess-association-list -version|-help|-manual ecaccess-association-list [-debug] [-gateway name] [association-name] DESCRIPTION
List all your ECtrans Associations. When an association-name is specified then the details for this Association is displayed. ARGUMENTS
association-name (optional) The name of the Association to retrieve the details. OPTIONS
-gateway name This is the name of the ECaccess Gateway where the Associations are installed. It is by default the Gateway you are connected to. In order to get the name of your current Gateway you can use the ecaccess-gateway-name command. When using the commands at ECMWF the default Gateway is always "ecaccess.ecmwf.int". -version Display version number and exits. -help Print a brief help message and exits. -manual Prints the manual page and exits. -debug Display the SOAP messages exchanged. EXAMPLES
ecaccess-association-list List all your Associations on your default Gateway. ecaccess-association-list -gateway ecaccess.ecmwf.int ginko List the details of the Association ginko on the ecaccess.ecmwf.int Gateway. SEE ALSO
ecaccess-association-delete, ecaccess-association-get, ecaccess-association-protocol, ecaccess-association-put and ecaccess. perl v5.14.2 2012-04-16 ECACCESS-ASSOCIATION-LIST(1p)
All times are GMT -4. The time now is 07:12 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy