Sponsored Content
Operating Systems Solaris Jumpstart Solaris Installation Program screen Post 302247204 by Diabolist on Wednesday 15th of October 2008 07:22:18 AM
Old 10-15-2008
Sorry, not sure I'm clear. Did you remove it completely, or try setting it to this (or both):

timeserver=localhost

You're timezone is mis-spelled. Was that a cut-n-paste?
 

10 More Discussions You Might Find Interesting

1. Solaris

Jumpstart installation problem.

We are installing Solaris 9 with Jumpstart ...facing problems.. Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly. when we give "boot net - install" at OK prompt, it is coming till "The system is coming up. Please wait" After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies

2. Solaris

Solaris 10 installation over WAN using jumpstart

I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies

3. Solaris

Error in Solaris installation over WAN(unix: Could not start init) Program terminated

I am trying to install Solaris 10 on a target machine which is t1000. ( sun4v). I have configured my jumpstart server to install solaris over WAN. when i boot my machine, the wanboot image gets downloaded properly, miniroot gets downloaded properly, but after that the process fails with the... (3 Replies)
Discussion started by: hemalsid
3 Replies

4. Solaris

Flash installation with Jumpstart

I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following #more flash_profile_test install_type flash_install archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies

5. Solaris

jumpstart installation

hi friends, i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server please help me thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies

6. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies

7. Solaris

Could not start installation using jumpstart

hello I created a boot server and tryed to run intstall with jumpstart on other solaris server, but jumpstart coudn't starts, only text-based install. sysidcfg and rules file are in the same shared folder, rules file has only one string any - - any_profile - and thta't all. also I created... (2 Replies)
Discussion started by: sluge
2 Replies

8. Solaris

help me! jumpstart installation error

Hi actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies

9. Solaris

Solaris 10 flash installation - fatal error. Solaris installation program exited.

Not very helpful to say the least. Seems to read the flar file and go through the upgrade and then come up with this error. Any ideas? (1 Reply)
Discussion started by: psychocandy
1 Replies

10. Solaris

Problem in configuring jumpstart installation

I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output bash-3.2# cat sysidcfg terminal=vt100 network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \ protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
timezone(4)							   File Formats 						       timezone(4)

NAME
timezone - default timezone data base SYNOPSIS
/etc/timezone DESCRIPTION
The timezone file contains information regarding the default timezone for each host in a domain. Alternatively, a single default line for the entire domain may be specified. Each entry has the format: Timezone-name official-host-or-domain-name Items are separated by any number of blanks and/or TAB characters. A `#' indicates the beginning of a comment; characters up to the end of the line are not interpreted by routines which search the file. The timezone is a pathname relative to the directory /usr/share/lib/zone- info. This file is not actually referenced by any system software; it is merely used as a source file to construct the NIS timezone.byname map. This map is read by sysidtool(1M) to initialize the timezone of the client system at installation time. For more information, see the Solaris Express Installation Guide: Basic Installations. The timezone file does not set the timezone environment variable TZ. See TIMEZONE(4) for information to set the TZ environment variable. EXAMPLES
Example 1 Typical timezone line Here is a typical line from the /etc/timezone file: US/Eastern East.Sun.COM #Sun East Coast FILES
/etc/timezone SEE ALSO
sysidtool(1M), TIMEZONE(4) Solaris Express Installation Guide: Basic Installations SunOS 5.11 18 Feb 2003 timezone(4)
All times are GMT -4. The time now is 06:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy