10-15-2008
Sorry, not sure I'm clear. Did you remove it completely, or try setting it to this (or both):
timeserver=localhost
You're timezone is mis-spelled. Was that a cut-n-paste?
10 More Discussions You Might Find Interesting
1. Solaris
We are installing Solaris 9 with Jumpstart ...facing problems..
Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly.
when we give "boot net - install" at OK prompt, it is coming till
"The system is coming up. Please wait"
After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies
2. Solaris
I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies
3. Solaris
I am trying to install Solaris 10 on a target machine which is t1000. ( sun4v). I have configured my jumpstart server to install solaris over WAN. when i boot my machine, the wanboot image gets downloaded properly, miniroot gets downloaded properly, but after that the process fails with the... (3 Replies)
Discussion started by: hemalsid
3 Replies
4. Solaris
I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following
#more flash_profile_test
install_type flash_install
archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies
5. Solaris
hi friends,
i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server
please help me
thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies
6. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
7. Solaris
hello
I created a boot server and tryed to run intstall with jumpstart on other solaris server, but jumpstart coudn't starts, only text-based install. sysidcfg and rules file are in the same shared folder, rules file has only one string
any - - any_profile - and thta't all. also I created... (2 Replies)
Discussion started by: sluge
2 Replies
8. Solaris
Hi
actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies
9. Solaris
Not very helpful to say the least. Seems to read the flar file and go through the upgrade and then come up with this error.
Any ideas? (1 Reply)
Discussion started by: psychocandy
1 Replies
10. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
PASTE(1) BSD General Commands Manual PASTE(1)
NAME
paste -- merge corresponding or subsequent lines of files
SYNOPSIS
paste [-s] [-d list] file ...
DESCRIPTION
The paste utility concatenates the corresponding lines of the given input files, replacing all but the last file's newline characters with a
single tab character, and writes the resulting lines to standard output. If end-of-file is reached on an input file while other input files
still contain data, the file is treated as if it were an endless source of empty lines.
The options are as follows:
-d list Use one or more of the provided characters to replace the newline characters instead of the default tab. The characters in list
are used circularly, i.e., when list is exhausted the first character from list is reused. This continues until a line from the
last input file (in default operation) or the last line in each file (using the -s option) is displayed, at which time paste
begins selecting characters from the beginning of list again.
The following special characters can also be used in list:
newline character
tab character
\ backslash character
Empty string (not a null character).
Any other character preceded by a backslash is equivalent to the character itself.
-s Concatenate all of the lines of each separate input file in command line order. The newline character of every line except the
last line in each input file is replaced with the tab character, unless otherwise specified by the -d option.
If '-' is specified for one or more of the input files, the standard input is used; standard input is read one line at a time, circularly,
for each instance of '-'.
The paste utility exits 0 on success, and >0 if an error occurs.
SEE ALSO
cut(1)
STANDARDS
The paste utility is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
BSD
June 6, 1993 BSD