|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
multi-network question
Post 302245823 by mik on Saturday 11th of October 2008 07:45:39 AM
10-11-2008
multi-network question
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ?
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ?
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hey,
Just need a little help I'm not sure wat I should do.
We have several little networks setup for testing different things. One of these networks we need to have running at full dulpex.
Right now we run 2 hubs (to go off to 2 differnt parts) and they are half dulpex hubs.
Is is... (1 Reply)
Discussion started by: merlin
1 Replies
2. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
3. IP Networking
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
Discussion started by: scofiled83
2 Replies
4. IP Networking
Folks;
I have 2 SUSE servers similar in all configuration & both on the same network
(192.168.151.10 & 192.168.151.11) with the same default gateway of 192.168.151.1 and the same netmask of 255.255.255.0 and the same firewall configuration
the first one works fine and i can ssh to it & i can... (3 Replies)
Discussion started by: Katkota
3 Replies
5. Programming
Assume we have an application built on *nix that uses fork()...then the processes procedure is going to act as follow:
X is considered a parent process (first click on application)
Y is considered a child process of X (second click on application)
Z is considered a child process of Y (third... (6 Replies)
Discussion started by: f.ben.isaac
6 Replies
6. Solaris
Dear All
I have three site in multi city and have in three site
ADSL connection with Fixed IP and three Connection leased line
(VHSDSL) and
and the primary connection it's VHSDSL and BAckup up connection ADSL
So can i use IPMP in solaris OS 10 in three Site to have this Service
in three Site... (0 Replies)
Discussion started by: Hosam
0 Replies
7. IP Networking
Hi,
We currently operate a DHCP Server on Vxworks system.
It seems that the server is functioning only over the boot interface.
While trying to use it on a different interface the DHCP client messages seems to reach the interface but stay without response.
From a... (1 Reply)
Discussion started by: zohara
1 Replies
8. Shell Programming and Scripting
Hi,
I have a problem where I need to make this input:
nameRow1a,text1a,text2a,floatValue1a,FloatValue2a,...,floatValue140a
nameRow1b,text1b,text2b,floatValue1b,FloatValue2b,...,floatValue140b
look like this output:
nameRow1a,text1b,text2a,(floatValue1a - floatValue1b),(floatValue2a -... (4 Replies)
Discussion started by: nricardo
4 Replies
9. Shell Programming and Scripting
awk -F "" '/<Id>|<id>|<Source>|<source>|<Accession>|<accession>|<TestName>|<testname>/ {print $2, $3}' OFS='\t' Test.xml
The above code works great, but lets say I wanted the <Analyte> name (<Name>STAT3). The word <name> is unique so there will be multiple records pulled. Is there a way to... (8 Replies)
Discussion started by: cmccabe
8 Replies
10. UNIX for Advanced & Expert Users
I have a question regarding IPTables packet flow, that I am hoping I can get an answer to.
We have a fairly advanced implementation of IPTables that I am trying to convert into a third party product and I am not quite certain on the packet flow in the current IPTables implementation.
We are... (2 Replies)
Discussion started by: knightfirefx
2 Replies
LEARN ABOUT DEBIAN
aoe-discover
aoe-discover(8) System Manager's Manual aoe-discover(8) NAME
aoe-discover - tell aoe driver to discover AoE devices SYNOPSIS
aoe-discover DESCRIPTION
The aoe-discover command tells the aoe driver to discover ATA over Ethernet (AoE) devices on the network. All network interfaces will be probed with a AoE config query broadcast. If the aoe-interfaces command has limited the allowable network interfaces, only devices discovered via allowable interfaces will become available. The default is to make available all AoE devices found on all accessible ethernet networks. It's good to run the aoe-discover command after running aoe-interfaces. EXAMPLE
In this example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic. After remembering that shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then calls aoe-discover to ask the aoe driver to look for new AoE devices. nai:~# modprobe aoe aoe_iflist="eth0" nai:~# aoe-stat e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 nai:~# aoe-discover nai:~# aoe-stat e7.0 eth3 up e7.1 eth3 up e7.2 eth3 up e7.3 eth3 up e7.4 eth3 up e7.5 eth3 up e7.6 eth3 up e7.7 eth3 up e7.8 eth3 up e7.9 eth3 up e10.9 eth0 up SEE ALSO
aoe-interfaces(8), aoe-stat(8), aoetools(8). AUTHOR
Ed L. Cashin (ecashin@coraid.com) aoe-discover(8)