hi all
iam trying to set my eri0 interface but with little luck .
when i set the ip using ipconfig i always get "bad adress"..
moreover when i use ifconfig eri0 i can notice that the inet is 0.0.0.0 and the netmask 0
i am runnig solaris 9 on sparc .
any helpis highly appreciated ... ... (2 Replies)
if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host (1 Reply)
Hello,
I have a server with two ip addresses. I need to make the ip address that's currently the secondary the primary. How do I use the ifconfig command and primary option?
Thanks. (5 Replies)
HI All,
My interface card has failed.If i am giving the command to uplumb it i am getting an error.
ce401001: flags=219040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED,CoS> mtu 1500 index 3
inet 10.188.24.18 netmask ffffffc0 broadcast 10.188.24.63
# ifconfig... (2 Replies)
Hello All,
Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a.
i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on.
thanks (1 Reply)
I'm a newbie to linux, so pleases forgive me!
I would like to find a script that I could use to extract a dynamic ip from the ppp0 and set it as a variable to be used in IPTables
basically, if ppp0 ip address is 10.10.10.20, I would like a script that would set a var to 10.10.10.0. of... (9 Replies)
I'm working on an AIX Unix LPAR (AIX 3.5 00C3C9904C00 as returned by uname -a)
I can access this box using telnet, port 22 using adress IP A and B
A=AA.AA.XX.XX and B=AA.AA.YYY.YYY
I can confirm these 2 are the same space, I can see
I can't find address B listed anywhere... so I wonder what... (1 Reply)
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Hi
I am trying to create a script extracting the IP provided by ifconfig.
I tried with grep + awk but I am returned more than I need.
/sbin/ifconfig eth0 | grep "inet addr:" | awk '/inet addr:/ { print $2 }'
and returns
addr:10.15.1.64
How can I remove "addr:" string?... (9 Replies)
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
LEARN ABOUT MINIX
ifconfig
IFCONFIG(8) System Manager's Manual IFCONFIG(8)NAME
ifconfig - configure a TCP/IP device
SYNOPSIS
ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv]
DESCRIPTION
Ifconfig initializes a TCP/IP device setting the IP address and/or netmask. It will report the address and netmask set. This command may
be used if the system has not been configured properly yet. It is only used at boot time to set a fixed address for a system without a
physical ethernet. Normally the inet task will find it out by itself from the RARP server.
OPTIONS -h The decimal TCP/IP address to set.
-n The netmask to set.
-i Don't set the IP address or netmask if already set. This way ifconfig cannot interfere if the numbers have been found out by RARP.
-v Report IP address and netmask. This is the default action if there are no other options.
SEE ALSO hostaddr(1), rarpd(8), set_net_default(8), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
IFCONFIG(8)