10-02-2008
Qlogic HBA card in E450 with errors
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot sequence, before the Openboot banner appears:
Unimplemented FCode token before address fff0dce9
Warning: Fcode sequence resulted in a net stack depth change of 1
Also the following messages appear during boot up:
WARNING: /pci@1f,4000/scsi@3 (glm0):
SCSI bus DATA IN phase parity error
Target 0 reducing sync. transfer rate
Target 0 disabled wide SCSI mode
Target 0 reverting to async. mode
Can you tell me whether I have a problem with the cable or the card or both? How do I troubleshoot this?
Thanks so much
Margaret
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
3. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
4. Solaris
Hi all
Hope your all well and happy in solaris land :-)
Recently purchased some Qlogic HBA's for a few solaris servers. Was told that you cant have mixed chipsets and as this client is all qlogic, have to have hba's using qlogic.
1) Is that correct ? Cant mix different chipsets of... (0 Replies)
Discussion started by: sbk1972
0 Replies
5. Solaris
Hi all,
New to the world of SAN, so forgive me for any ambigious terminology.
I have a sun 6800 chassis with two domains, both domains connected to a San ancor sanbox ( 2 x Storeedge T3 / Mcdata switch ). Current Qlogic HBA's are 1Gb glc adaptors, version of qlc drivers... (1 Reply)
Discussion started by: sbk1972
1 Replies
6. Solaris
Hi All,
I'm actually trying to configure a Qlogic HBA on a solaris9 connecting in a Brocade SAN. I installed Solaris9 and now trying to look at FC devices..
bash-2.05# luxadm -e port
Found path to 0 HBA ports
bash-2.05# luxadm probe
No Network Array enclosures found in /dev/es... (7 Replies)
Discussion started by: ilan
7 Replies
7. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
8. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
9. Red Hat
need to do LUN masking at qlogic HBA level..at RHEL 5.x
I am using qla* module at part of the Unix kernel, it is not OEM drivers that come with the HBA card, so I can't use Sansurfer to do this..
Is there a way to do this at all ??
:wall: (0 Replies)
Discussion started by: ppchu99
0 Replies
10. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
LEARN ABOUT OPENSOLARIS
hba_refreshinformation
HBA_RefreshInformation(3HBAAPI) Common Fibre Channel HBA Information Library Functions HBA_RefreshInformation(3HBAAPI)
NAME
HBA_RefreshInformation, HBA_RefreshAdapterConfiguration - refresh information for a specific HBA
SYNOPSIS
cc [ flag... ] file... -lHBAAPI [ library... ]
#include <hbaapi.h>
void HBA_RefreshInformation(HBA_HANDLE handle);
void HBA_RefreshAdapterConfiguration(void);
PARAMETERS
handle an open handle returned from HBA_OpenAdapter(3HBAAPI)
DESCRIPTION
The HBA_RefreshInformation() function requests that the underlying VSL reload all information about the given HBA. This function should be
called whenever any function returns HBA_STATUS_ERROR_STALE_DATA, or if an index that was previously valid returns HBA_STATUS_ERROR_ILLE-
GAL_INDEX. Because the underlying VSL can reset all indexes relating to the HBA, all old index values must be discarded by the caller.
The HBA_RefreshAdapterConfiguration() function updates information about the HBAs present on the system. This function does not change any
of the relationships between the HBA API and adapters that have not been reconfigured. HBA handles continue to refer to the same HBA even
if it is no longer installed. The HBA name or index assigned by the library remains assigned to the same HBA even if it has been removed
and reinstalled, as long as the bus position, WWN, and OS device have not changed. Adapter that have been removed and not replaced cannot
have their HBA handles, HBA names, and HBA indexes reassigned. Calls to these adapters will generate HBA_STATUS_ERROR_UNAVAILABLE.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-------------------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-------------------------------------+
|Interface Stability |Standard: FC-MI 1.92 (API version 1) |
+-----------------------------+-------------------------------------+
| |Standard: FC-HBA Version 4 (API ver- |
| |sion 2) |
+-----------------------------+-------------------------------------+
|MT-Level |Safe |
+-----------------------------+-------------------------------------+
SEE ALSO
HBA_OpenAdapter(3HBAAPI), libhbaapi(3LIB), attributes(5)
T11 FC-MI Specification
SunOS 5.11 1 Sep 2003 HBA_RefreshInformation(3HBAAPI)