Thanks for the reply but it's not quite what I need.
As you can see (I forgot to mention), $NAME can also contain a hyphen sometimes so counting them out in the sed doesn't work half the time. $VERSION should always contain digits but may also contain letters. $ARCH could have either numbers and/or letters (native or i486). And $BUILD can also have both.
If I'm working with a package name like "xpaint-2.7.8.1-i486-2", then my old sed works fine.
Thanks again. Much appreciated.
Hi ,
I have a question. How do I replace 2 words in one line like this
IN CLO07 INDEX IN CLOIX07
to
IN CLO07_S02 INDEX IN CLOIX07_S02
But one thing to remember is that there are lots of words like CLODM001 .
So the only matching pattern is "IN CLO"
sample file... (4 Replies)
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
I'd like to extract the temps from the following command via a series of sed statements but the actual syntax is beyond me.
$ nc localhost 7634 ... (2 Replies)
Hi,
I want to read a command value and replace the command value in another file.
Anybody know how to write it???
For example:
File A:
Command1 = test
File B:
Command1 =
Command2 =
Command3 =
I want to write a shell script to read content from File A and replace Command1... (3 Replies)
Friends,
I came across a wierd scenario while using sed. When I use the below cmd sequence at OS prompt it works fine:
sed 's/# TMOUT=120/TMOUT=900/g' /etc/profile > /etc/profile.011211
However when I use the same in a script it throws the following error:
==Error==
sed: 0602-404... (4 Replies)
Gurus,
I am trying to display a match (single character) from beginning of the line in a file using a variable.
I tried using sed ... not sure where am doing it wrong...
sed -n "/^\$variable/p" FileName.shor
sed -n "/^\${variable}/p" FileName.shBoth of the above are not working.....Thanks... (4 Replies)
Hi,
Can anyone let me know the sed command usage
requirement:
sed 's/standard/standard_and/' <new.txt>new.txt
here it needs to search for the pattern "standard" in the file new.txt and it should replace as "standard_and" in the same file new.txt
Note: new.txt is having a separator... (8 Replies)
Discussion started by: srikanth_sagi
8 Replies
LEARN ABOUT OPENSOLARIS
native
native(5) Standards, Environments, and Macros native(5)NAME
native - native branded zone
DESCRIPTION
The native brand uses the branded zones framework described in brands(5) to run zones installed with the same software as is installed in
the global zone. The system software must always be in sync with the global zone when using a native brand.
SUB-COMMANDS
The following native brand-specific subcommand options are supported in zoneadm(1M).
attach [-u] [-b patchid]...
For native zones, zoneadm checks package and patch levels on the machine to which the zone is to be attached. If the packages/patches
that the zone depends on from the global zone are different (have different revision numbers) from the dependent packages/patches on
the source machine, zoneadm reports these conflicts and does not perform the attach. If the destination system has only newer dependent
packages/patches (higher revision numbers) than those on the source system, you can use the -u option to update the attached zone to
match the -revision packages and patches that exist on the new system. With -u, as in the default behavior, zoneadm does not perform an
attach if outdated packages/patches are found on the target system.
For native zones, one or more -b options can be used to specify a patch ID for a patch installed in the zone. These patches will be
backed out before the zone is attached or, if -u was also specified, updated.
install [-a archive] | [-d path] [-p] [-s] [-u] [-v] [-b patchid]...
The native brand installer supports installing the zone from either the software already installed on the system or from an image of an
installed system running the same release. This can be a full flash archive (see flash_archive(4)) or a cpio(1) or pax(1) "xustar" ar-
chive. The cpio archive be compressed with gzip or bzip2. The image can also be a level 0 ufsdump(1M), a path to the top-level of a
system's root tree, or a pre-existing zone path.
With no options the zone is installed using same software as is running the global zone.
To install the zone from a system image either the -a or -d is required. Either the -u or -p option is also required in this case.
-a archive
The path to a flash_archive(4), cpio(1), or pax(1) "xustar" archive, or a level0 ufsdump(1M), of an installed system. cpio archives
may be compressed using gzip or bzip2.
-b patchid
One or more -b options can be used to specify a patch ID for a patch installed in the system image. These patches will be backed
out during the installation process.
-d path
The path to the root directory of an installed system. If path is a hyphen (-), the zonepath is presumed to be already populated
with the system image.
-p
Preserve the system configuration after installing the zone.
-s
Install silently.
-u
Run sys-unconfig(1M) on the zone after installing it.
-v
Verbose output from the install process.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWzoneu |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO cpio(1), pax(1), zlogin(1), zonename(1), sys-unconfig(1M), ufsdump(1M), zoneadm(1M), zonecfg(1M), flash_archive(4), attributes(5),
brands(5), privileges(5), zones(5), lx_systrace(7D)SunOS 5.11 13 Feb 2009 native(5)