09-21-2008
can ping doing this?..
i have question about this problem,,
could i ping ip address with the range 192.168.1.1 - 192.168.2.200 ?
ip address begin from 192.168.1.1 until 192.168.2.200 ?
could ping (not fping) doing that?
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
When I pinged a machin, I got to be seen a different kind of
reply from that machine.
This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message.
So what does this mean.
Regards & Thanks in advance.
Vishwa. (4 Replies)
Discussion started by: S.Vishwanath
4 Replies
2. UNIX for Dummies Questions & Answers
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
Discussion started by: nemex
2 Replies
3. AIX
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies
4. UNIX for Dummies Questions & Answers
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Discussion started by: sam70
1 Replies
5. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
6. IP Networking
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Discussion started by: Rutgerncas
7 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
arpsend
arpsend(8) Containers arpsend(8)
NAME
arpsend - send ARP requests
SYNOPSIS
arpsend -D -e target_ip [ -e target_ip ...] [-c count] [-w timeout] interface
arpsend -U -i source_ip [-c count] [-w timeout] interface
DESCRIPTION
Utility arpsend sends ARP packets on device interface to detect or update neighbours' ARP caches with a given IP.
COMMANDS
Run utility with one of the following commands:
-D Send broadcast ARP request to detect neighbours with target_ip. You have to specify target_ip (-e option).
-U Send broadcast ARP request to update neighbours' ARP caches with source_ip. You have to specify source_ip (-i option).
OPTIONS
-c count
Number of packets to send. Default is infinity.
-w interval
Interval between packets, in seconds. Default is 1 second.
-i source_ip_address
Set source IP address field in ARP packet.
-e target_ip_address
Set target IP address field in ARP packet. Note that you can specify -e option multiple times to detect many IP addresses in one
utility call.
EXIT STATUS
arpsend returns 0 upon successful execution. If something goes wrong, it returns an appropriate error code.
1 EXC_USAGE
Usage error
2 EXC_SYSTEM
System error
3 EXC_RECV
ARP reply was received
EXAMPLES
To send request on interface eth0 to detect any neighbour computers with IP 192.168.10.200:
arpsend -D -e 192.168.10.200 eth0
To send request on interface eth0 to update neighbours' ARP caches with IP 192.168.10.200:
arpsend -U -i 192.168.10.200 eth0
NOTES
Interface you use have to be arpable and not be loopback (i.e. /sbin/ip link show interface should show neither NOARP nor LOOPBACK flags
in interface parameters).
SEE ALSO
vzctl(8).
LICENSE
Copyright (C) 2000-2011, Parallels, Inc. Licensed under GNU GPL.
OpenVZ 28 Jun 2011 arpsend(8)