09-17-2008
free
top
vmstat
then you use maths to get percentage
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
When i re-updated my system i set my swap at 500 MB. I have 256 in ram and have never even gone into the 250 mb of swap that i had originally configured. How do I reduce the swap? (3 Replies)
Discussion started by: macdonto
3 Replies
2. UNIX for Dummies Questions & Answers
Is it really so that if swap will be located in the begining of hard drive, than it will work faster? (1 Reply)
Discussion started by: Ty3
1 Replies
3. Solaris
When i try to type swap -l ,nothing come out but blinking.
May i know what is the problem and solutions ?
thanks (6 Replies)
Discussion started by: Farbegas
6 Replies
4. Solaris
Hello and thanks in advance.
I have a Sun box with raid 1 on the O/S disks using solaris svm.
I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space.
I have been warned not to do this by some... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
5. HP-UX
I have a HP-UX B.11.23 server with 16 gb of memory 84 gb of swap configured. I am being pushed to define more swap to try and get more Tuxedo domains to start. At what point do we have too much swap for the amount of memory? Thanks in advance. (11 Replies)
Discussion started by: scotbuff
11 Replies
6. Red Hat
free -m : 1023 total swap space
created default partition /dev/sdb1 50M using fdisk. i did write the changes.
#mkswap /dev/sdb1
#swapon /dev/sdb1
free -m : 1078 total swap space
this shows that the swap is on
Question : i did not change the type LINUX SWAP (82) in fdisk.
so why is... (5 Replies)
Discussion started by: dplinux
5 Replies
7. HP-UX
Hi
I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system:
- I would like to know when does the memory swap space spill over to the device swap space?
- And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
Discussion started by: lamoul
6 Replies
8. Red Hat
Hi,
I have added a new disk to production server. How to make it visible to os and how to configure it. I also want to add some space from that disk to swap space. Please help me out. (1 Reply)
Discussion started by: chetansingh23
1 Replies
9. Solaris
Hi,
Can somebody please help here, since iam just a beginner.
According to my book knowledge.
the Avalilable memory calculated by swap -l (includes only swap) should be small as compared to swap -s value(includes Virtual memory=swap +physical).
but this is quite opposite in my case.
swap... (6 Replies)
Discussion started by: Laxxi
6 Replies
10. Solaris
Hi Solaris Folks :),
I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands.
$swap -s
total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available
$swap -l
swapfile dev swaplo... (6 Replies)
Discussion started by: seenuvasan1985
6 Replies
LEARN ABOUT REDHAT
vmstat
VMSTAT(8) Linux Administrator's Manual VMSTAT(8)
NAME
vmstat - Report virtual memory statistics
SYNOPSIS
vmstat [-n] [delay [ count]]
vmstat[-V]
DESCRIPTION
vmstat reports information about processes, memory, paging, block IO, traps, and cpu activity.
The first report produced gives averages since the last reboot. Additional reports give information on a sampling period of length delay.
The process and memory reports are instantaneous in either case.
Options
The -n switch causes the header to be displayed only once rather than periodically.
delay is the delay between updates in seconds. If no delay is specified, only one report is printed with the average values since boot.
count is the number of updates. If no count is specified and delay is defined, count defaults to infinity.
The -V switch results in displaying version information.
FIELD DESCRIPTIONS
Procs
r: The number of processes waiting for run time.
b: The number of processes in uninterruptable sleep.
w: The number of processes swapped out but otherwise runnable. This
field is calculated, but Linux never desperation swaps.
Memory
swpd: the amount of virtual memory used (kB).
free: the amount of idle memory (kB).
buff: the amount of memory used as buffers (kB).
Swap
si: Amount of memory swapped in from disk (kB/s).
so: Amount of memory swapped to disk (kB/s).
IO
bi: Blocks sent to a block device (blocks/s).
bo: Blocks received from a block device (blocks/s).
System
in: The number of interrupts per second, including the clock.
cs: The number of context switches per second.
CPU
These are percentages of total CPU time.
us: user time
sy: system time
id: idle time
NOTES
vmstat does not require special permissions.
These reports are intended to help identify system bottlenecks. Linux vmstat does not count itself as a running process.
All linux blocks are currently 1k, except for CD-ROM blocks which are 2k.
FILES
/proc/meminfo
/proc/stat
/proc/*/stat
SEE ALSO
ps(1), top(1), free(1)
BUGS
Does not tabulate the block io per device or count the number of system calls.
AUTHOR
Written by Henry Ware <al172@yfn.ysu.edu>.
Throatwobbler Ginkgo Labs 27 July 1994 VMSTAT(8)