09-09-2008
Yes I had set-defaults, this chip that is malfunctioning , do you know how to fix it or do you know if it is serious? You said something about Veritas?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi
Should anyone be able to help, one of my colleagues was doing a truss this morning and I am not sure if it has offset the system crash, but we have had these type of errors coming up????
# ls
ls: Cannot read /usr/lib/ld.so.1
Killed
# ps -ef
ps: Cannot read /usr/lib/ld.so.1
Killed
#... (1 Reply)
Discussion started by: NAV4869
1 Replies
2. UNIX for Advanced & Expert Users
I am just getting started loading an Enterprise 450 Dell with Solaris 9 however I cannot get out of a loop that is not letting me get started.
My basic question is what are the key strokes to get you out of a boot sequence so that you can at least clear the hard drive or start an install
... (9 Replies)
Discussion started by: Joe7778
9 Replies
3. Solaris
Hi,
I have a Sun 3500 server on which i installed solaris 8 and have also installed veritas 4.0 on it. i dont know why from the time i have built this server whenever i try to boot it, the server doesnot come back smooth.... i have got to connect a laptop to the serial port of the server and... (3 Replies)
Discussion started by: ishila
3 Replies
4. Solaris
Hi experts,
I have bought a used SUN Enterprise 250 server that currently runs solaris 8. Ive downloaded solaris 10 (sparc edition) from sun.com, and have burned the iso files to cd roms. So far so good.
I can log into the system via the serial interface (port A).
I want to sweep the discs,... (21 Replies)
Discussion started by: congo
21 Replies
5. Solaris
I am needing to install solaris 2.6 on a Enterprise 420R with 4X450mHz. Documentation says you need Operating Enviroment Installation CD February 2000(704-7076-10). Does anyone know where I can get this? (4 Replies)
Discussion started by: jenyart
4 Replies
6. IP Networking
Hello,
My config:
SLES 10 sp1
Apache / drupal / mysql
I have a saturation of TCP ports on this hosts. Hosting about 60 websites. The event tonight was ~200 hits minutes.
With "netstat-n" I see ~5500 connections. Including approximately 3800 in FIN_WAIT1.
As a first step I would... (3 Replies)
Discussion started by: lilech
3 Replies
7. Solaris
Good day,
I am dummie on solaris and trying learning about Solaris, so no much experience, this is my problem, I got enterprise 4500 SUN Sparc hardware, has 2 internal SCSI HD, when I try to install Solaris 10 says that "no disk found" at middle of installation, I already change the HD and the... (3 Replies)
Discussion started by: edgargarcia_y2k
3 Replies
8. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
9. Solaris
Booting problem on Sun 3500
Hi,
I have a Sun 3500 server on which i installed solaris 5.2 installed . i dont know why from the time i have built this server whenever i try to boot it, the server doesnot come back smooth.i got a message Sync file system than restart
some times showing ok... (2 Replies)
Discussion started by: najeer
2 Replies
10. Solaris
I need help to resurrect very old netra machines.
two of them are netra enterprise 2 and they do not boot with the message
Cant open boot device
The IDPROM contents are invalid
Boot device: net File and args
the host is not connected to any LAN
I brought up another Netra 5 connected to... (3 Replies)
Discussion started by: rk2153
3 Replies
LEARN ABOUT CENTOS
i2c-stub-from-dump
I2C-STUB-FROM-DUMP(8) System Manager's Manual I2C-STUB-FROM-DUMP(8)
NAME
i2c-stub-from-dump - feed i2c-stub with dump files
SYNOPSIS
i2c-stub-from-dump address[,address,...] dump-file [dump-file ...]
DESCRIPTION
i2c-stub-from-dump is a small helper script for the i2c-stub kernel driver. It lets you setup one or more fake I2C chips on the i2c-stub
bus based on dumps of the chips you want to emulate.
i2c-stub-from-dump requires i2cdetect and i2cset to be installed and reachable through the user's PATH. The former is used to find out the
i2c-stub bus number, while the latter is used to write to the fake I2C chips.
EXAMPLE
You have an I2C chip on system A. You would like to do some development on its driver on system B. Here are the few steps you have to fol-
low.
On system A, use i2cdump to capture a dump from the chip. Assuming that the chip in question lives at address 0x4c on I2C bus 0, you would
run:
i2cdump -y 0 0x4c b > chip.dump
Adjust the bus number and chip address for your case. i2cdetect can help you find out their values. If the device uses word (16-bit) regis-
ter access instead of the traditional byte (8-bit) access, use mode w instead of b.
Copy the dump file to system B.
On system B, run:
i2c-stub-from-dump 0x4c chip.dump
This will load the required i2c-dev and i2c-stub kernel drivers if needed, then write all the register values to the emulated I2C chip at
address 0x4c. Again, adjust the address as needed.
LIMITATIONS
There are some limitations to the kind of devices that can be handled:
o Device must not have banks (as most Winbond devices do).
SEE ALSO
i2cdump(8), i2cdetect(8), i2cset(8)
AUTHOR
Jean Delvare
March 2010 I2C-STUB-FROM-DUMP(8)