Sponsored Content
Operating Systems Solaris ALOM NETMGT port settings (sc/rsc) Post 302233490 by incredible on Sunday 7th of September 2008 10:50:10 PM
Old 09-07-2008
And also there are only few much param where you can manipulate the settings.. but not on speed or duplex.
if_network="true"
if_modem="false"
if_connection="ssh"
if_emailalerts="false"
sys_autorestart="xir"
sys_bootrestart="none"
sys_bootfailrecovery="none"
sys_maxbootfail="3"
sys_xirtimeout="900"
sys_boottimeout="900"
sys_wdttimeout="60"
netsc_tpelinktest="true"
netsc_dhcp="false"
netsc_ipaddr="192.168.1.5"
netsc_ipnetmask="255.255.255.0"
netsc_ipgateway="192.168.1.1"
mgt_mailhost=""
mgt_mailalert=""
sc_customerinfo=""
sc_escapechars="#."
sc_powerondelay="false"
sc_powerstatememory="false"
sc_clipasswdecho="true"
sc_cliprompt="sc"
sc_clitimeout="0"
sc_clieventlevel="2"
sc_backupuserdata="true"
sys_eventlevel="2
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

console access via serial port - settings

looking for the answer to console port access via 25pin serial. Can i tip in from another unix box for access? (5 Replies)
Discussion started by: simplimarvelous
5 Replies

2. UNIX for Advanced & Expert Users

RMI Port settings for different users

I have installed an application on AIX 5.3, however when i log in as the application owner i cannot open the RMI Port 1099. If i log in as root i can open the RMI port. Is there a specific setting that determines if a user can open the RMI port? I cannot add this user as part of SYS Admin group. ... (2 Replies)
Discussion started by: speedo
2 Replies

3. UNIX for Advanced & Expert Users

RSC question?

Has anyone had a message after attempting a telnet to an RSC server of: "Console session already in use." I'm attempting to access this server to setup a user account, and I'm having some problems. Does anyone have an idea or suggestion on how to proceed? (0 Replies)
Discussion started by: mr-synapse
0 Replies

4. AIX

P520 AIX com port (tty0) settings

I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line The settings are correct in both sides, But I can't establish a connection. I suspect that there's something that I should do regarding the... (3 Replies)
Discussion started by: ayman metwally
3 Replies

5. UNIX for Dummies Questions & Answers

No Responses from ALOM using NET MGNT PORT on SunFire v245

Please Help... I have two sunfire V245 servers running Apache on Solaris 5.10. Both servers have the same settings and apps. Before we used serial port to connect to ALOM 1.6. We switched to net mgnt port because of virtualization of all our servers. Situation: Server 1 applied the solaris... (1 Reply)
Discussion started by: glieu
1 Replies

6. Solaris

RSC configuration

Hi All, Please send the configuration for RSC in solaris. Thanks and Regards, (3 Replies)
Discussion started by: lbreddy
3 Replies

7. Solaris

LOM ALOM ILOM ELOM RSC SP commands equivalent

Has anyone got an equivalent commands sheet for all Sun's serial or network management ports? (1 Reply)
Discussion started by: son_t
1 Replies

8. Solaris

Sun 8 +RSC

Hi All I have done a reboot for SUN Solaris 8 ( model SUNFIRE 280R) but i havent got the OK prompt i only got the following: RSC2 POST - Version 10-18-2000 0.7 Dual Port Memory Test, PASSED. TTY External - Internal Loopback Test TTY External - Internal Loopback Test, PASSED. ... (3 Replies)
Discussion started by: alaa75
3 Replies

9. Solaris

Difference b/n ALOM and ALOM CMT

Hi Everyone. What is the differece b/n ALOM and ALOM CMT Service processor. I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports. Not sure how different are these. Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies

10. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
oidentd_masq.conf(5)						File Formats Manual					      oidentd_masq.conf(5)

NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file. DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file. oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option. This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons for windows do this, maybe others). FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type> The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is equivalent to 255.255.0.0, etc. The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param- eter. The third field specifies the operating system the machine matching the first parameter is running. EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type> 192.168.1.1 someone UNIX 192.168.1.2 noone WINDOWS 192.168.1.1/32 user1 UNIX 192.168.1.0/24 user3 UNIX 192.168.0.0/16 user4 UNIX somehost user5 UNIX 192.168.1.0/255.255.255.0 user6 UNIX AUTHOR
Ryan McCabe <ryan@numb.org> http://dev.ojnk.net SEE ALSO
oidentd(8) oidentd.conf(5) version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)
All times are GMT -4. The time now is 02:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy