09-05-2008
Need help to configure Adaptec AHA-2930CU
Need a procedure on how to configure adaptec SCSI pci card.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi people
I am having problems getting a few Sun Station to work again. We just moved to a new building with new IPs and new gateways. I need to change all these settings. Could some one please tel me what files I have to change.
It is a Solaris 5.7 machine.
Thanx
O:confused: (2 Replies)
Discussion started by: Orange
2 Replies
2. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
1 Replies
3. UNIX for Dummies Questions & Answers
Does anyone know what driver is used for the Adaptec 29160 SCSI controller? (3 Replies)
Discussion started by: promed
3 Replies
4. UNIX for Dummies Questions & Answers
Trying to install Sco OSR 6.0 on Dell Optiplex with SERIAL ATA ADADPTEC 1210SA controller.
Sco says its sipported by the AACRAID driver but on installation its says that it doesnt recognise the partitions
In the middle of re-formatting at the moment - just wondered if anyone had anu... (0 Replies)
Discussion started by: farmacy
0 Replies
5. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
6. Solaris
Hi ,
I installed Xming on my laptop .
I have a remote server Sun Solaris 10, When I lanch xlaunch and do these
export DISPLAY=10.149.132.111:0.0
xterm &
Myserver:/Allsuite/test/dev/ENV23>xterm &
15071
Myserver:/Allsuite/test/dev/ENV23>bash: xterm: command not found
It works fine... (1 Reply)
Discussion started by: dashok.83
1 Replies
7. Solaris
Hi All,
Can you please help me in configuring mail server on Solaris 10?
Will appreciate if I can get some link which can explain the steps
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
8. UNIX and Linux Applications
Hey everyone.
I am trying to set up four sun servers. They all came with an adaptec storagetek raid liveCD. On the liveCD there is a utility called "Arcconf" which is supposed to be used to configure the storage arrays. The example given in their documentation uses this as an example:
ARCCONF... (2 Replies)
Discussion started by: msarro
2 Replies
9. UNIX for Dummies Questions & Answers
hello,
I'm trying install apache http server version 2.2.22.
I downloaded the file httpd-2.2.22.tar.bz2.
I unzipped this file..
When I type "./configure", the following error occurs:
# ./configure --prefix=/opt/work/apache2.2.22
checking for chosen layout... Apache
checking for... (1 Reply)
Discussion started by: Adriano Schmidt
1 Replies
10. AIX
Hi,
We've upgraded the AIX few weeks ago. Now i see a new filesystem. Can you please give some info about this? How we can make use of this fs?
Please provide me any appropriate links.
/>df -g /aha
Filesystem GB blocks Free %Used Iused %Iused Mounted on
/aha -... (3 Replies)
Discussion started by: System Admin 77
3 Replies
AHA(4) BSD Kernel Interfaces Manual AHA(4)
NAME
aha -- Adaptec SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device aha
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
aha_load="YES"
In /boot/device.hints:
hint.aha.0.at="isa"
DESCRIPTION
This driver provides access to the SCSI bus connected to the Adaptec AHA-154x and AHA-1640 SCSI host adapters. x is 0 for controllers with-
out a floppy drive and 2 for controllers that have them. For optimum performance, Adaptec AHA-174x controllers should be configured in
enhanced mode and attached via the ahb(4) driver.
One device hint entry for every card to be attached by the system is required. Specific values for the port address, IRQ, and DRQ may be
specified. If wildcard values are used, the driver will query the device for its current settings and use those. If the port address is a
wildcard, the driver consults an internal table of possible port address locations and attaches to the first unattached card it finds. The
possible port addresses for this card are 0x330, 0x334, 0x230, 0x234, 0x130, and 0x134.
The AHA-1640 is an MCA bus card. Since the MCA bus is a self-identifying bus, no setting of hints is required.
HARDWARE
The aha driver supports the following SCSI host adapters:
o Adaptec AHA-154xB
o Adaptec AHA-154xC
o Adaptec AHA-154xCF
o Adaptec AHA-154xCP
o Adaptec AHA-1640
o Adaptec AHA-174x in 154x emulation mode
o DTC 3290 SCSI controller in 1542 emulation mode
o Tekram SCSI controllers in 154x emulation mode
SEE ALSO
ahb(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)
AUTHORS
The aha driver was ported by M. Warner Losh from the bt driver written by Justin T. Gibbs.
BUGS
The AHA-154xA card does not support residuals on data transfers. As a result, this card is no longer supported.
There have been some reports that the AHA-154xB does not work well under heavy load.
The AHA-154xCP is a plug and play controller. However, its resources are set using the on-board BIOS and cannot be moved. Failures to
attached for this card are often caused when the resources set in the BIOS conflict.
BSD
July 4, 2004 BSD