Sponsored Content
Operating Systems Solaris A1000 Solaris 10 on Blade 1000 Post 302229987 by tribbles on Thursday 28th of August 2008 10:49:06 AM
Old 08-28-2008
A1000 Solaris 10 on Blade 1000

I have a SUN Blade 1000 running Solaris 10 and an A1000 array.
I know that this combo is not supported by SUN but will it work?
The raid manager software is installed and it says that the firmware needs to be upgraded -it is at I think level 2.05 something.
I can see all the disks in a probe-scsi-all but get errors when the system boots.
Should I upgrade the firmware? Do you know what patch to apply to do this?
Is there something more up to date than rm6 that would manage this setup?
Thanks
 

8 More Discussions You Might Find Interesting

1. UNIX Benchmarks

Sun Blade 2000 UltraSparc III Solaris 8

Sun Blade 2000 UltraSparc III Solaris 8 Notes: prtdiag: System Configuration: Sun Microsystems sun4u SUNW,Sun-Blade-1000 (UltraSPARC-III+) System clock frequency: 150 MHZ Memory size: 3GB ==================================== CPUs ==================================== ... (0 Replies)
Discussion started by: tnorth
0 Replies

2. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies

3. Solaris

SunBlade 1000, 'blocked' when trying to install Solaris 10

HW: SunBlade 1000 w/2x CPUs, DVD-ROM, XVR-1200 SW: Solaris 10 DVDs direct from Sun Tried: probing scsi, boot -r, reset-all When booting off cd: boot cdrom Boot device: /pci@8, 700000/scsi/scsi@6/disk@6,0:f File and args: SunOS Release 5.10 Version Generic_141444-09 64-bit Copyright... (8 Replies)
Discussion started by: boolean2
8 Replies

4. Solaris

Solaris: Blade 150 - XWINDOWS Problem

Hi, I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console. But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies

5. Hardware

Sun Blade 1000 keyboard not detected.

Hello, I have a sun blade 1000 machine, it passes post, has 2 750mhz sparc 3 cpus and has 4GB of ram. I have setup a TIP connection and did everything i could to figure what the hell is going on, but I cannot it seems to me that the usb ports are not giving out any power. I've tried all... (0 Replies)
Discussion started by: binary0x01
0 Replies

6. UNIX for Dummies Questions & Answers

Reinstalling Solaris 9 on Sun Blade 100

For the past ten years I have owned a blade 100, and I had Solaris 9 running on it. Due to the fact, 9 is woefully out of date, I wanted to try 10, but 10 needed more ram, so I beefed up the ram to the full 2 gig. I have two 15 gig ide drives in the box (stock drives). But unfortunately solaris... (2 Replies)
Discussion started by: RichardET
2 Replies

7. Solaris

help installing solaris 10 on sun blade 1500

Hi everyone can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom? Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies

8. Solaris

Cannot install or run Solaris 8 on Sun Blade 150

Hi everybody, I'm having big troubles in installing Solaris 8 on a Sun Blade 150. Here are some system specs: Sun Blade 150 (UltraSPARC-IIe 550MHz) RAM: 256MB OBP 4.10.6 2003/06/06 12:30 POST 2.0.1 2001/08/23 17:13 When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
EFICHECK(8)						    BSD System Manager's Manual 					       EFICHECK(8)

NAME
eficheck -- check the integrity of the x86 flash chip firmware. SYNOPSIS
eficheck --integrity-check [-h EFI-hash-input-file] [-b EFI-binary-input-file] eficheck --show-hashes [-h EFI-hash-input-file] [-b EFI-binary-input-file] eficheck --generate-hashes [-h EFI-hash-output-file] [-p output-path] eficheck --save [-b EFI-binary-output-file] eficheck --cleanup [-b EFI-binary-input-and-output-file>] eficheck --version eficheck --help DESCRIPTION
eficheck is a tool to check the x86 flash chip firmware. The following commands can be used with eficheck: --integrity-check hashes portion of the firmware and compares against known-good hashes --generate-hashes outputs hashes for a given firmware to be used as known-good hashes --show-hashes shows the hashes for the sub-sections of the firmware which are measured --save saves the full flash chip contents to a binary file. Requires root privileges. --cleanup zeros any privacy-sensitive data (such as nvram), enabling the file to be shared for analysis. --version print out eficheck version number. --help display a short help. EXAMPLES
'eficheck --save -b firmware.bin' Save this system's EFI firmware as firmware.bin 'eficheck --cleanup -b firmware.bin' Overwrite the EFI variables portion of the firmware.bin, in place 'eficheck --generate-hashes' Analyze the current system's installed EFI firmware, and store the hashes into hash file(s) in current folder File name(s) will be selected according to image's EFI version(s) 'eficheck --generate-hashes -b firmware.bin' Analyze the firmware.bin, and store the hashes into hash file(s) in current folder. Filename will be based on the detected firmware version. 'eficheck --generate-hashes -p /usr/local/allowlists' Analyze the current system's installed EFI firmware, and store the hashes into hash file(s) in /usr/local/allowlists folder 'eficheck --integrity-check' Attempt to automatically determine which firmware you are running, and integrity check against the appropriate file, and report any differences 'eficheck --integrity-check -h /usr/libexec/firmwarecheckers/eficheck/EFIAllowListShipping.bun- dle/allowlists/IM171.88Z.0105.B08.1604111319.0.ealf' Compare the current system's EFI firmware against the Apple-provided expected measurements for an "iMac17,1" at firmware revision B08, and report any differences 'eficheck --integrity-check -h hash.ealf -b firmware.bin' Compare the given hash file against against the given firmware image and report any differences 'eficheck --show-hashes' Print the hashes for the current system's installed EFI firmware to stdout 'eficheck --show-hashes -b firmware.bin' Print the hashes for the given firmware.bin to stdout 'eficheck --show-hashes -h IM171.88Z.0105.B08.1604111319.0.ealf' Print the hashes for the given allowlist to stdout May 25, 2017
All times are GMT -4. The time now is 11:52 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy