08-27-2008
can't ping IP
hi ,
i have problem that i can't ping machine , machine is in running state but i can't access or ping it .. but when i restarts that machine it works fine.
can anybody have an idea abou this problem ..
thanks
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
When I pinged a machin, I got to be seen a different kind of
reply from that machine.
This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message.
So what does this mean.
Regards & Thanks in advance.
Vishwa. (4 Replies)
Discussion started by: S.Vishwanath
4 Replies
2. UNIX for Dummies Questions & Answers
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
Discussion started by: nemex
2 Replies
3. AIX
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies
4. UNIX for Dummies Questions & Answers
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Discussion started by: sam70
1 Replies
5. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
6. IP Networking
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Discussion started by: Rutgerncas
7 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
rds-ping
RDS-PING(1) BSD General Commands Manual RDS-PING(1)
NAME
rds-ping -- test reachability of remote node over RDS
SYNOPSIS
rds-ping [-c count] [-i interval] [-I local_addr] remote_addr
DESCRIPTION
rds-ping is used to test whether a remote node is reachable over RDS. Its interface is designed to operate pretty much the standard ping(8)
utility, even though the way it works is pretty different.
rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is
bound; instead, the kernel processes incoming packets and responds to them.
OPTIONS
The following options are available for use on the command line:
-c count
Causes rds-ping to exit after sending (and receiving) the specified number of packets.
-I address
By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address
(i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source
address). Using the -I option, you can override this choice.
-i timeout
By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout
value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds
or microseconds, respectively.
Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results.
AUTHORS
rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>.
SEE ALSO
rds(7), rds-info(1), rds-stress(1).
BSD
Apr 22, 2008 BSD