Sponsored Content
Special Forums IP Networking Assigning a vertual IP and doing IP multipathing... Post 302228808 by prashantshukla on Monday 25th of August 2008 01:12:07 PM
Old 08-25-2008
Thank DUKENUKE2 for ur Help.....
 

10 More Discussions You Might Find Interesting

1. Solaris

solaris multipathing

I have solaris 10 sparc. I installed a Qlogic hba card. This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay. I formated 2 luns. On my solaris system, i have 4 disk. How to configure solaris 10 to fix the dual disk view. ... (4 Replies)
Discussion started by: simquest
4 Replies

2. Solaris

Solaris IP Multipathing

Hi, I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation . I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2. Now is it possible to have IP Multipathing on each of the servers as follows ? ... (0 Replies)
Discussion started by: maadhuu
0 Replies

3. AIX

Is there any vertual AIX syste,

Hello guys as i new to AIX i need to know is there any virtual system for AIX i want to practice and i don have IBM machine !!! any help (4 Replies)
Discussion started by: F_A_H_D
4 Replies

4. UNIX for Dummies Questions & Answers

Disk Multipathing - How do I setup?

Hi, I've been asked to setup disk multipathing (not IP multipathing) I have searched the internet and found limited documents, I have found one http://dlc.sun.com/pdf/819-0139-12/819-0139-12.pdf but I am struggling to understand it. Does anyone have any links I can use that will tell me... (2 Replies)
Discussion started by: newbiesolaris10
2 Replies

5. Solaris

Solaris multipathing

Hai we using emc storage which is conneted to M5000 through san switch. we asign 13 luns but in server it is showing 22 luns. i enable the solaris multipathing (MPxIO) #more /kernel/drv/fp.conf in that file MPxio-disable=no #mpathadm list lu it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies

6. Solaris

Multipathing - problem

Hello, I turned on the server multipathing: # uname -a SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140 stmsboot -D fp -e And after a reboot the server, multipathing is not enable: # stmsboot -L stmsboot: MPxIO is not enabled stmsboot: MPxIO disabled # ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies

7. Red Hat

How to Cleanup Multipathing

I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist. # multipath -l mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX \_ round-robin 0 \_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies

8. AIX

Multipathing in AIX

Hi, I know the concept of multipathing, but would like to know how to configure multipathing in AIX. or software/driver is by default present in AIX?????? How to find out wheather multipathing is configured in AIX????? Regards, Manu (4 Replies)
Discussion started by: manoj.solaris
4 Replies

9. Linux

Linux multipathing issue...

Hi folks. When issuing a multipath -ll on my server, i see something that is bugging me... # multipath -ll 2000b0803ce002582 dm-10 Pillar,Axiom 600 size=129G features='0' hwhandler='0' wp=rw |-+- policy='round-robin 0' prio=50 status=active | |- 0:0:0:4 sdd 8:48 active ready running... (0 Replies)
Discussion started by: Stephan
0 Replies

10. Red Hat

Verify multipathing

I have a couple of questions regarding multipath. If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13 If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure? Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
certmonger(1)						      General Commands Manual						     certmonger(1)

NAME
ipa-getcert SYNOPSIS
ipa-getcert request [options] ipa-getcert resubmit [options] ipa-getcert start-tracking [options] ipa-getcert stop-tracking [options] ipa-getcert list [options] ipa-getcert list-cas [options] DESCRIPTION
The ipa-getcert tool issues requests to a org.fedorahosted.certmonger service on behalf of the invoking user. It can ask the service to begin enrollment, optionally generating a key pair to use, it can ask the service to begin monitoring a certificate in a specified location for expiration, and optionally to refresh it when expiration nears, it can list the set of certificates that the service is already moni- toring, or it can list the set of CAs that the service is capable of using. If no command is given as the first command-line argument, ipa-getcert will print short usage information for each of its functions. The ipa-getcert tool behaves identically to the generic getcert tool when it is used with the -c IPA option. BUGS
Please file tickets for any that you find at https://fedorahosted.org/certmonger/ SEE ALSO
certmonger(8) getcert-list(1) getcert-list-cas(1) getcert-request(1) getcert-resubmit(1) getcert-start-tracking(1) getcert-stop-tracking(1) certmonger-certmaster-submit(8) certmonger-ipa-submit(8) certmonger_selinux(8) certmonger Manual 3 November 2009 certmonger(1)
All times are GMT -4. The time now is 02:59 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy