08-24-2008
10 More Discussions You Might Find Interesting
1. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
2. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
3. AIX
Hello guys
as i new to AIX i need to know is there any virtual system for AIX i want to practice and i don have IBM machine !!!
any help (4 Replies)
Discussion started by: F_A_H_D
4 Replies
4. UNIX for Dummies Questions & Answers
Hi,
I've been asked to setup disk multipathing (not IP multipathing) I have searched the internet and found limited documents, I have found one
http://dlc.sun.com/pdf/819-0139-12/819-0139-12.pdf but I am struggling to understand it.
Does anyone have any links I can use that will tell me... (2 Replies)
Discussion started by: newbiesolaris10
2 Replies
5. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
6. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
7. Red Hat
I have a server running redhat 5.5 and it has one SAN device presented to it as LUN9. How can I clean up the remaining entries. I cannot afford to interupt the service. Please assist.
# multipath -l
mpath0 (36000097000019260298953666633436) dm-11 EMC,SYMMETRIX
\_ round-robin 0
\_ 2:0:0:9 ... (2 Replies)
Discussion started by: Tirmazi
2 Replies
8. AIX
Hi,
I know the concept of multipathing, but would like to know how to configure multipathing in AIX.
or software/driver is by default present in AIX??????
How to find out wheather multipathing is configured in AIX?????
Regards,
Manu (4 Replies)
Discussion started by: manoj.solaris
4 Replies
9. Linux
Hi folks.
When issuing a multipath -ll on my server, i see something that is bugging me...
# multipath -ll
2000b0803ce002582 dm-10 Pillar,Axiom 600
size=129G features='0' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=50 status=active
| |- 0:0:0:4 sdd 8:48 active ready running... (0 Replies)
Discussion started by: Stephan
0 Replies
10. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
LEARN ABOUT POSIX
ip-token
IP-TOKEN(8) Linux IP-TOKEN(8)
NAME
ip-token - tokenized interface identifier support
SYNOPSIS
ip token { COMMAND | help }
ip token set TOKEN dev DEV
ip token del dev DEV
ip token get [ dev DEV ]
ip token [ list ]
DESCRIPTION
IPv6 tokenized interface identifier support is used for assigning well-known host-part addresses to nodes whilst still obtaining a global
network prefix from Router advertisements. The primary target for tokenized identifiers are server platforms where addresses are usually
manually configured, rather than using DHCPv6 or SLAAC. By using tokenized identifiers, hosts can still determine their network prefix by
use of SLAAC, but more readily be automatically renumbered should their network prefix change [1]. Tokenized IPv6 Identifiers are described
in the draft [1]: <draft-chown-6man-tokenised-ipv6-identifiers-02>.
ip token set - set an interface token
set the interface token to the kernel.
TOKEN the interface identifier token address.
dev DEV
the networking interface.
ip token del - delete an interface token
delete the interface token from the kernel.
dev DEV
the networking interface.
ip token get - get the interface token from the kernel
show a tokenized interface identifier of a particular networking device. Arguments: coincide with the arguments of ip token set but the
TOKEN must be left out.
ip token list - list all interface tokens
list all tokenized interface identifiers for the networking interfaces from the kernel.
SEE ALSO
ip(8)
AUTHOR
Manpage by Daniel Borkmann
iproute2 28 Mar 2013 IP-TOKEN(8)