swap -d failure Post: 302227049

10 More Discussions You Might Find Interesting

1. Programming

ld failure

Hi, I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples...

2. Solaris

swap -l

When i try to type swap -l ,nothing come out but blinking. May i know what is the problem and solutions ? thanks

3. Solaris

Swap config - Mirror swap or not?

Hello and thanks in advance. I have a Sun box with raid 1 on the O/S disks using solaris svm. I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space. I have been warned not to do this by some...

4. HP-UX

How much Swap is too much?

I have a HP-UX B.11.23 server with 16 gb of memory 84 gb of swap configured. I am being pushed to define more swap to try and get more Tuxedo domains to start. At what point do we have too much swap for the amount of memory? Thanks in advance.

5. UNIX for Advanced & Expert Users

su failure

Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to...

6. Red Hat

swap not defined as swap

free -m : 1023 total swap space created default partition /dev/sdb1 50M using fdisk. i did write the changes. #mkswap /dev/sdb1 #swapon /dev/sdb1 free -m : 1078 total swap space this shows that the swap is on Question : i did not change the type LINUX SWAP (82) in fdisk. so why is...

7. HP-UX

Swap device file and swap sapce

Hi I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system: - I would like to know when does the memory swap space spill over to the device swap space? - And how much % of memory swap utilization should be specified (swap space device...

8. UNIX for Dummies Questions & Answers

boot up failure unix sco after power failure

hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless.

9. Solaris

swap

Hi, Can somebody please help here, since iam just a beginner. According to my book knowledge. the Avalilable memory calculated by swap -l (includes only swap) should be small as compared to swap -s value(includes Virtual memory=swap +physical). but this is quite opposite in my case. swap...

10. Solaris

Explain the output of swap -s and swap -l

Hi Solaris Folks :), I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands. $swap -s total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available $swap -l swapfile dev swaplo...

LEARN ABOUT FREEBSD

if_hme

HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME

     hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device miibus
	   device hme

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_hme_load="YES"

DESCRIPTION

     The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.

     All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
     transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.

HARDWARE

     The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.

     Cards supported by the hme driver include:

     o	 Sun PCI SunSwift Adapter (``SUNW,hme'')
     o	 Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
     o	 Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
     o	 Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
     o	 Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
     o	 Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')

NOTES

     On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
     using the setenv command or by eeprom(8).	If set to ``false'' (the default), the hme driver will use the system's default MAC address for
     all of its devices.  If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
     address.

     Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
     add-on cards except the single-port SBus versions.

SEE ALSO

     altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)

     Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide,
     http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf, April 1996.

HISTORY

     The hme driver first appeared in NetBSD 1.5.  The first FreeBSD version to include it was FreeBSD 5.0.

AUTHORS

     The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.

BSD
								   June 14, 2009							       BSD

10 More Discussions You Might Find Interesting

1. Programming

ld failure

Discussion started by: handak9

2. Solaris

swap -l

Discussion started by: Farbegas

3. Solaris

Swap config - Mirror swap or not?

Discussion started by: BG_JrAdmin

4. HP-UX

How much Swap is too much?

Discussion started by: scotbuff