Sponsored Content
Operating Systems Linux second NIC not working - D-Link DGE 530 T Post 302226604 by Corne on Tuesday 19th of August 2008 10:36:37 AM
Old 08-19-2008
Quote:
Originally Posted by bryanabhay
after adding sk98lin this name in modules.conf
have you modprobe sk98lin to update the info for kernel ?
yes, i have done the

modprobe sk98lin
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Drivers to HP 530

Hi Gurus of Unix, Well. I have a Laptop Model HP-530, I want to install Solaris, in this equipment. the question is You know the driver that will be compatible with this type of model, like this: HP 530 Notebook PC- Download drivers and software - HP Business Support Center If you know the... (1 Reply)
Discussion started by: andresguillen
1 Replies

2. Hardware

D-Link DGE-530T (not TX) driver HELP

Where can I find DGE 530T driver for Unix (SCO)? There is one on D-Link page, which package includes WinX drivers, MacOS....etc, Linux and Unix. But I cannot find Unix driver whithin, cause there is no dir for unix driver. Thnx for future help. (3 Replies)
Discussion started by: PNemesis
3 Replies

3. UNIX for Advanced & Expert Users

I suspect that my NIC is working in hybridization mode?

Hi, all: The physical network interface card should drop the packets if it doesn't match the MAC address of the NIC. In my PC, however, the packets which shoud be dropped trigger the interrupt function of my own driver and are recieved as skb to be transfered to the upper layer! Why? How... (1 Reply)
Discussion started by: liklstar
1 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. SuSE

530 Login incorrect

Hi I upgraded my Suse linux server and installed a complete new server with suse ver 11. I copied the passwd and shadow files from the old Suse 10 to the new Suse 11 server (/etc) Now I get "530 Login incorrect" error when I try to FTP into an account with correct username and password. Can... (1 Reply)
Discussion started by: Tony.Marshall
1 Replies

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

7. Solaris

Solaris zone with full working NIC

I want a solaris zone,wich can get ip from dhcp external server i configure my zone net: address not specified allowed-address not specified configure-allowed-address: true physical: vnic1 defrouter not specified vnic is linked to net0 dladm net0 ... (6 Replies)
Discussion started by: Linusolaradm1
6 Replies

8. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

9. Solaris

Solaris link aggregation not working as expected

Hi, This is Solaris-10 x86 platform. I am not able to ping gateway associated with aggr50001. I am not getting idea, where could be issue. Please advise. # netstat -nr Routing Table: IPv4 Destination Gateway Flags Ref Use Interface --------------------... (10 Replies)
Discussion started by: solaris_1977
10 Replies
DH_INSTALLMODULES(1)						     Debhelper						      DH_INSTALLMODULES(1)

NAME
dh_installmodules - register kernel modules SYNOPSIS
dh_installmodules [debhelperoptions] [-n] [--name=name] DESCRIPTION
dh_installmodules is a debhelper program that is responsible for registering kernel modules. Kernel modules are searched for in the package build directory and if found, preinst, postinst and postrm commands are automatically generated to run depmod and register the modules when the package is installed. These commands are inserted into the maintainer scripts by dh_installdeb(1). FILES
debian/package.modprobe Installed to etc/modprobe.d/package.conf in the package build directory. OPTIONS
-n, --no-scripts Do not modify preinst/postinst/postrm scripts. --name=name When this parameter is used, dh_installmodules looks for and installs files named debian/package.name.modprobe instead of the usual debian/package.modprobe NOTES
Note that this command is not idempotent. dh_prep(1) should be called between invocations of this command. Otherwise, it may cause multiple instances of the same text to be added to maintainer scripts. SEE ALSO
debhelper(7) This program is a part of debhelper. AUTHOR
Joey Hess <joeyh@debian.org> 11.1.6ubuntu2 2018-05-10 DH_INSTALLMODULES(1)
All times are GMT -4. The time now is 03:58 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy