07-28-2008
Are you trying to set up a tunnel ? Something like:
hosts_behind_NAT>============[server]
Did you set up routing on the hosts?
Did you set up routes back?
are tunnel interfaces up?
moreover you said your server has just one interface: eth0,
did you mean one internal,LAN interface, or one at all (no WAN )???
honestly I don't have much experience with pptp,
more with GRE... but the question is interesting
10 More Discussions You Might Find Interesting
1. IP Networking
Hi
I know this problem is more likely some windows problem but it has also something to do with unix.
We have a windows nt environment wich uses AIX (unix) machines as file servers (samba). In our windows network environment we nicely see al the unix file servers via the 10 MB network. Last... (2 Replies)
Discussion started by: Mark Detrez
2 Replies
2. IP Networking
following Problem.
I configured my SuSE Linux 8.0 as a router. I4l, named, ip_forward, iptables (NAT/MASQUERADING) are running or are aktivatet.
I just can get a internet connection about the proxy server squid, but if i want to use other protocols i need functional routing.
(I had this... (1 Reply)
Discussion started by: razor
1 Replies
3. IP Networking
I have a question concerning networking. Could any forum
members explain to me why I might be getting "no route
to host" messages when I try to connect through ftp and
http protocols?
I have went to my etc/hosts file and everything seems to be
configured properly. I can connect within my... (1 Reply)
Discussion started by: cstovall
1 Replies
4. IP Networking
hi,
below is the situation:
my server is in 128.10.200.xxx network.
i have a solaris computer running in a subnet. this computer got 2 nic card.
1 is 172.18.198.xxx , another 1 is 10.100.xxx.11
there is a machine stick with this computer, ip is 10.100.xxx.12
so, 10.100.xxx.11 and... (3 Replies)
Discussion started by: kyhah
3 Replies
5. Solaris
Hi,
I got problem of Sun Solaris 8 routing.
IP of SunA is 10.16.64.164, and have routing table:
10.16.64.0 10.16.64.164 U 1 19236 bge1
10.6.0.0 10.6.0.3 U 1 16534 bge0
224.0.0.0 10.6.0.3 U 1 ... (4 Replies)
Discussion started by: milo
4 Replies
6. Red Hat
hi,
having an issue on a class C network with trying to get a redhat diskless setup going. I am using oracle enterprise 5, which is RHEL 5.3 i believe.
here is the scenario:
sun sparc m4k that i am planning on making the red hat boxes boot off after i get the network issue fixed.
... (3 Replies)
Discussion started by: caddyjoe77
3 Replies
7. AIX
I need the following solution , please help me...
Current situation
ip: 192.168.0.12 persistent and 192.168.254.12 service ip
gateway: 192.168.0.254
subnet: 255.255.255.0
i have added a new ip on a new nic
ip: 10.10.255.40
gateway: 10.10.255.62
subnet: 255.255.255.224
... (1 Reply)
Discussion started by: rajibimran
1 Replies
8. IP Networking
hi guys!
I was searching few days for a solution to my problem but haven't found one or I'm too dumb to understand.
Here's what happened:
I have a linux server used as a router. It has an eth0 and eth1 (local interface). I just installed openvpn (I need it only as a client), I configured it and... (0 Replies)
Discussion started by: shamora
0 Replies
9. IP Networking
Internet Gateway
192.168.0.201
Server 1
192.168.0.101
192.168.1.101
192.168.2.101
gateway: 192.168.0.201
VIP: 192.168.1.100
VIP: 192.168.2.100
Server 2
192.168.0.102
192.168.1.102
192.168.2.102
gateway: 192.168.0.201
Client 1
192.168.2.201
gateway: 192.168.2.100 (1 Reply)
Discussion started by: hopfensp
1 Replies
10. Solaris
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Discussion started by: sri243
1 Replies
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD