07-25-2008
what models of sun/hp you looking at? i have an idea but it depends on how many varieties of servers you have.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi Does anyone know the command to configure HP tape slots. I have tried the following on Sun, but its notworking. This is the first time I have configured a tape drive with muiltple slots.
root@ssdb0009 # cfgadm -l
Ap_Id Type Receptacle Occupant Conditio... (3 Replies)
Discussion started by: dennisca
3 Replies
2. Filesystems, Disks and Memory
Hello,
I'm running Red Hat Linux on a Dell Poweredge 2650 Rack Server and wondered if anyone knew of a tool or command I could use to probe the memory slots on the motherboard.
I know the machine has six memory slots and currently contains 1GB RAM, what I don't know however, is if it contains... (3 Replies)
Discussion started by: cw1972
3 Replies
3. Solaris
Has anyone ever relocated an HBA card after already having it configured in another PCI slot? I've found that the HBA instance #'s start incrementing past the previous. It results in me having to have my instance numbers in /kernel/drv/qla2300.conf be 4,5,6,7 instead of 0,1,2,3. Cleanup with... (5 Replies)
Discussion started by: kduffin
5 Replies
4. Solaris
Due to speed mismatch, the server kept crashing. Sun suggests that I need to move the two HBA cards from the 66Mhz to the 33Mhz slots. There are tons of disks that are connected to these HBAs and I have Veritas volume manager.
Does anyone have a list of what I need to do prior/after moving to... (3 Replies)
Discussion started by: kiem
3 Replies
5. Solaris
I've got lots of scsi transport errors on the E2900 - the HBA was replaced once out of curiosity but the problem still exists.
Feb 15 07:03:11 ivsdbch2 scsi: WARNING: /ssm@0,0/pci@18
,600000/SUNW,jfca@1,1/fp@0,0/ssd@w5005076300c889cb,4 (ssd21):
Feb 15 07:03:11 ivsdbch2 SCSI transport... (1 Reply)
Discussion started by: kiem
1 Replies
6. Solaris
Hi All,
Can Any body tell me how to find out the how many memory slots are there in SUN server ??
Thanks and Regards, (2 Replies)
Discussion started by: lbreddy
2 Replies
7. AIX
A while back I had a command that shows the memory slots (and info on the modules inserter) in an IBM AIX machine. I cannot remember it at this time, can someone help me out with this command please? (4 Replies)
Discussion started by: bbbngowc
4 Replies
8. AIX
Hi, all. I was wondering if there's a command or log file that will tell me how much RAM is in the system and, more specifically, the size of each stick.
Thanks,
Jason (3 Replies)
Discussion started by: JasonRkr
3 Replies
9. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
10. Solaris
I tried to reinstall GRUB2 on my previous Solaris 11.3 installation but could not figure out why "bootadm install-bootloader" failed. Now I am trying to reinstall Solaris 11.3 instead, over my old Solaris partition. I am using the USB Live media ISO with the GUI. Installation fails with this... (0 Replies)
Discussion started by: kebabbert
0 Replies
LEARN ABOUT CENTOS
amtape
AMTAPE(8) System Administration Commands AMTAPE(8)
NAME
amtape - Control Amanda changers
SYNOPSIS
amtape [-o configoption...] config subcommand [subcommand_options...]
DESCRIPTION
Amtape is the command-line interface to Amanda's tape changers (amanda-changers(7)) and to the taperscan algorithm (amanda-taperscan(7)).
Tape changers maintain a notion of the current slot for each configuration. This may or may not correspond to an actual physical state of
the device, but is used by some taperscan algorithms to minimize searching through the slots.
Amtape uses the default changer. To use a different changer, use the config override option, e.g., -otpchanger=otherchanger.
SUBCOMMANDS
label label
Search for and load the Amanda tape with label [label], also setting the current slot.
slot slot
Load the volume in the given slot, also setting the current slot. The slot names current, next, first, and last have special meaning.
current
Shorthand for slot current.
inventory
Show the contents of all slots, based on the changer's cached metadata. This is a quick operation as it does not load or unload any
volumes, but is not supported by all changers.
show [slots]
Show the contents of all slots (or listed slots) by loading each slot and reading its label. This can be very slow. The slots arguments
is of the form 1,3-5,7.
reset
Reset the changer to a known state. This subcommand is intended to clear any unknown and potentially incorrect state the changer may
have stored.
eject [drive]
Eject the tape currently in the drive. This only applies to some changers. Specify a drive (by drive number) if more than one drive is
available.
clean [drive]
If a cleaning tape is defined for the changer, used it to clean the specified drive. The [drive] is optional if the changer only has
one drive.
taper
Run the taperscan algorithm (see amanda-taperscan(7)), displaying information about the progress of the scan.
update [what]
Update changer state. Consult amanda-changers(7) for changer-specific details on the format of what.
-o configoption
See the "CONFIGURATION OVERRIDE" section in amanda(8).
SEE ALSO
amanda(8), amanda-changers(7), amanda-taperscan(7), amanda-devices(7)
The Amanda Wiki: : http://wiki.zmanda.com/
AUTHORS
Dustin J. Mitchell <dustin@zmanda.com>
Zmanda, Inc. (http://www.zmanda.com)
James da Silva <jds@amanda.org>
Stefan G. Weichinger <sgw@amanda.org>
Amanda 3.3.3 01/10/2013 AMTAPE(8)