07-25-2008
The swapping of the disks not done yet. Noone is giving an answer to this and its very uncertain.Moreover , the user called up this morning and informed that the raid is not showing optimal and is still in sync state, which shoudn't be the case, cause I did the H/W RAID yesterday morning. even 500G, by now should be done, correct? Im lost.
he did a raidctl -l c1t0d0 and noticed the "sync" state
9 More Discussions You Might Find Interesting
1. Linux
Hi everyone.
I have a machine which upon to recently only had one hard disk. Now I have another one identical in size and speed and want create a raid set from those two.
The partition layout is that I have three partitions, first one for /boot, the second for / and then a huge LVM partition... (1 Reply)
Discussion started by: Sprellarinn
1 Replies
2. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
8. Red Hat
Im have Oracle Virtualbox and vmware workstation How can i Add2 HDD in Vmware or Virtualbox and Install centos Using Raid Configuration Please give me Tutorial step by Step .. Thanks in Advance
In Virtualbox there is SAS Hard disk So shall i Use it ? (3 Replies)
Discussion started by: babinlonston
3 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT OSX
glfencesync
GLFENCESYNC(3G) OpenGL 3.3 GLFENCESYNC(3G)
NAME
glFenceSync - create a new sync object and insert it into the GL command stream
C SPECIFICATION
GLsync glFenceSync(GLenum condition, GLbitfield flags);
PARAMETERS
condition
Specifies the condition that must be met to set the sync object's state to signaled. condition must be GL_SYNC_GPU_COMMANDS_COMPLETE.
flags
Specifies a bitwise combination of flags controlling the behavior of the sync object. No flags are presently defined for this operation
and flags must be zero.[1]
DESCRIPTION
glFenceSync creates a new fence sync object, inserts a fence command into the GL command stream and associates it with that sync object,
and returns a non-zero name corresponding to the sync object.
When the specified condition of the sync object is satisfied by the fence command, the sync object is signaled by the GL, causing any
glWaitSync(), glClientWaitSync() commands blocking in sync to unblock. No other state is affected by glFenceSync or by the execution of the
associated fence command.
condition must be GL_SYNC_GPU_COMMANDS_COMPLETE. This condition is satisfied by completion of the fence command corresponding to the sync
object and all preceding commands in the same command stream. The sync object will not be signaled until all effects from these commands on
GL client and server state and the framebuffer are fully realized. Note that completion of the fence command occurs once the state of the
corresponding sync object has been changed, but commands waiting on that sync object may not be unblocked until after the fence command
completes.
NOTES
glFenceSync is only supported if the GL version is 3.2 or greater, or if
the ARB_sync extension is supported.
.SH "ERRORS"
GL_INVALID_ENUM is generated if condition is not GL_SYNC_GPU_COMMANDS_COMPLETE.
GL_INVALID_VALUE is generated if flags is not zero.
Additionally, if glFenceSync fails, it will return zero.
SEE ALSO
glDeleteSync(), glGetSync(), glWaitSync(), glClientWaitSync()
COPYRIGHT
Copyright (C) 2010 Khronos Group. This material may be distributed subject to the terms and conditions set forth in the Open Publication
License, v 1.0, 8 June 1999. http://opencontent.org/openpub/.
NOTES
1.
flags is a placeholder for anticipated future extensions of fence sync object capabilities.
OpenGL 3.3 03/08/2011 GLFENCESYNC(3G)