07-22-2008
8 More Discussions You Might Find Interesting
1. Solaris
Hi All,
Can you please advise what the 't' letters stands for?
I understand the letter for the following "c1t1d0s2":
c = disk Controller
t = ?
d = disk number ID.
s = slice or partition of the disk
Thanks (2 Replies)
Discussion started by: tlee
2 Replies
2. Solaris
do anybody has a procedure for daily weekley monthly health check for SUN server with solaris OS?? (5 Replies)
Discussion started by: mm00123
5 Replies
3. Programming
Is there any possibility to develop an application using Visual Basic that connects to a unix server (using SSH) and run some commands?
I will try to describe what i need :
The user should enter the server adress, username and password!
Than the user must enter some "filenames" and after... (10 Replies)
Discussion started by: SuperDuck
10 Replies
4. Solaris
Dear all,
There wasn't any monitoring on our server except on the filesystem.
Therefore, I was wondering anything i should do on a daily basis to check on the server's status, health, hardware, or any other thing as a disaster prevention? Also, what command i should use to do that?
... (2 Replies)
Discussion started by: beginningDBA
2 Replies
5. Programming
I came across a puzzle which I can not explain. The setup is SCO OpenServer 5.7 (32 bit OS) and native SCO compiler. double is 8 bytes long on this system. I am able to populate the double variable with two different sets of values that produces the same double value, please see below:
#include... (7 Replies)
Discussion started by: migurus
7 Replies
6. Programming
I have an assignment in which a character is the input of which some bits(from a position to certain position) are to be inverted (1's complement) and then the resultant character is to be returned....for example
unsigned char x = J from p = 3 to offset n = 5
01001010 inverted to... (1 Reply)
Discussion started by: ezee
1 Replies
7. Red Hat
Hi, Earlier we used to reboot servers based on adhoc request, never checked anything on it pre-reboot., But now i need to reboot regularly but most of the info is not available, I need to know want to make sure that server to be rebooted without any issues, so I want to do few prechecks which will... (5 Replies)
Discussion started by: nanz143
5 Replies
8. UNIX for Beginners Questions & Answers
I have two files to be compared to get the output of the differences.
File1 has a lot more lists than File2.
After searching a lot on this thread I'am unable to find the exact code that im willing to get.
This will be used as 'pre-check'/post-check utility (health check Tool) to compare... (1 Reply)
Discussion started by: GeekyJimmy
1 Replies
LEARN ABOUT ULTRIX
rpc_use_family
rpc_use_family(3ncs) rpc_use_family(3ncs)
Name
rpc_use_family - create a socket of a specified address family for a remote procedure call (RPC) server (server only)
Syntax
#include <idl/c/rpc.h>
void rpc_$use_family(family, sockaddr, slength, status)
unsigned long family;
socket_$addr_t *sockaddr;
unsigned long *slength;
status_$t *status;
Arguments
family The address family of the socket to be created. The value must be one of socket_$internet or socket_$unspec.
sockaddr The socket address of the socket on which the server will listen.
slength The length, in bytes, of sockaddr.
status The completion status. If the completion status returned in is equal to status_$ok , then the routine that supplied it was
successful.
Description
The routine creates a socket for a server without specifying its port number. The RPC runtime software assigns a port number. If a server
must listen on a particular well-known port, use to create the socket.
A server listens on one socket per address family, regardless of how many interfaces that it exports. Therefore, servers should make this
call once per supported address family.
Examples
The following statement creates a server's socket:
rpc_$use_family (family, &saddr, &slen, &status);
Diagnostics
This section lists status codes for errors returned by this routine in
rpc_$cant_create_sock
The RPC runtime library was unable to create a socket.
rpc_$not_in_call An internal error.
rpc_$proto_error An internal protocol error.
rpc_$too_many_sockets
The server is trying to use more than the maximum number of sockets that is allowed; it has called or too many times.
rpc_$addr_in_use The address and port specified in an routine are already in use. This is caused by multiple calls to with the same
well-known port.
Files
See Also
intro(3ncs), rpc_use_family_wk(3ncs)
rpc_use_family(3ncs)