07-22-2008
Unable to use Crossbow commands ,completely?
Hi all,
I have begun working on a project that involves "Crossbow" technology.
But almost immediately i have run into problems!
My version of Solaris doesnt seem to have all the Crossbow commands at all.
Eg,
when i use,
#dladm create-vnic -d nge0 1
I get the entire set of dladm command that are allowed on my system!
however ,
dladm show-link,
works just fine?
It does not contain "create-vnic", rather had "create-vlan"
Now how do i figure out if my version supports crossbow or not
I am running snv 83.
And as far as i know ,the support must have gone in from 79a right?
Or are there any modules that needs to be enabled or downloaded to get this working?
Thanks
5 More Discussions You Might Find Interesting
1. Solaris
Hello,
I'll already apologize for my question, as it'll probably be hurting for an expert.
About two years ago I obtained a used Sun Ultra 10 with many accessoires for a very low price. I'm not much into UNIX (or rather not into it at all), but I wanted to play around a bit with it, especially as... (3 Replies)
Discussion started by: Superidiot
3 Replies
2. Solaris
Unable to execute commands using rsh in Solaris 9 and 10.
When I execute this command " rsh -n 172.16.67.91 ls -l " I am getting this error message.
::ffff:172.16.67.91: Connection refused
Please guide me how to enable rsh.
Thanks & Regards
Durgaprasad (1 Reply)
Discussion started by: durgaprasadr13
1 Replies
3. UNIX for Dummies Questions & Answers
I'm trying to run these commands (keylset,keylget) but i keep getting a error message "invalid command name "keylset"". I've tried running it on both ubuntu's terminal and also Evolane Tcl Engine. Any idea what could be the problem? (1 Reply)
Discussion started by: abe171
1 Replies
4. HP-UX
Hi All,
I want to get %cpu and %memory utilization for a given process id in HP-UX so am using the following commands
1)TOP -p <PID> am getting error message like Quitting top: pset 26323 doesn't exist,but when am using only TOP command without any options its working fine.
2)ps -e -o pcpu... (5 Replies)
Discussion started by: Ramya_Nm
5 Replies
5. Solaris
I am connecting a USB mass storage removeable drive to Solaris 10 x86 machine.
The device is detected and i am able to perform standard read and write functions.
But i want to use a code to send IOCTL based SCSI commands to the same device to read and write the data. Which i am unable to do so.... (17 Replies)
Discussion started by: danish2012
17 Replies
LEARN ABOUT XFREE86
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)