I am not sure what is wrong with my output. It is the output that I want.
Quote:
src ip dest ip #of flows total bytes
192.168.6.0 88.0.33.2 12 128
192.168.6.0 88.0.33.2 1 168
192.168.6.0 111.22.35.0 2 364
192.168.5.0 88.0.33.2 1 125
.....I want to count the unique destination, total flows and total bytes per sorce ip. The output that I want it to be is this
192.168.6.0 2 15 660
192.168.5.0 1 1 125
.....
From here, source 192.168.6.0 has 2 unique destination (88.0.33.22 and 111.22.35.0). and total of the flows is 12 (12+1+2) and total bytes 660 (128+168+364). So. from your code, I am trying to fit with my code. I am using awk -f count.awk. This are the lines in the count.awk file.
However, I got an error said that the src array is an illegal reference. Please help me. Need to solve this problem
Hi all,
I have some doubts in selecting the interface to transfer packets and receive the packets.
--> Multiple interfaces :
--------------------
1) 0.0.0.0 --------> wild card address.
2) x.x.x.x --------> valid address.(192.168.1.156)
3) ff.ff.ff.ff -------->... (0 Replies)
Move all files starting with a specific name to different directory.
This shell script program should have three parameters
File Name
Source Directory
Destination Directory
User should be able to enter ‘AB_CD*' in file name parameter. In this case all the files starting with AB_CD will... (1 Reply)
I'd like to specify a different build and deployment path for files, by default the same path is used for both build and install, I wasn't able to find a way to make these different. With Solaris pkgadd, one can specify different paths in prototype, so I would assume something like that is possible... (0 Replies)
Hi Everyone,
I am using solaris 10.I am facing a different problem here with tlsftp.I have intalled all steps for tlsftp and able to connect to the destination server from the source server.It worked for some days.But recently when i am connectin it is giving below error.I am... (0 Replies)
hi All,
i have 2 server setup now for Rsync, i configured Rsync on both of the server and it worked well when i did run from source to destination. and while running back from destination to source it produced this error:
bash-3.2$ ksh rsync_bravo_db.ksh usa0300uz1247.apps.mc.xerox.com... (0 Replies)
hi All, Any one answer my requirement.
I have source location
src_dir="/home/oracle/arun/IRMS-CM"
My Target location
dest_dir="/home/oracle/arun/LiveLink/IRMS-CM/$dc/$pc/$ct"
my source text files check with below example.text file content
$fn "\t" $dc "\t" $pc "\t" ... (3 Replies)
Hi Guys,
how to count number of files successfully copied while coping files from source to destination path
ex:10 files from source to target location copying
if 8 files copied successfully then
echo successfully copied=8
failure=2 files
if two files get error to coping files from... (23 Replies)
Is there a way to find out all the ports open between source IP & destination IP in any way ? (12 Replies)
Discussion started by: UnknownGuy
12 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD