Count total unique destination for source Post: 302213253

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Byte Rate to/from a source/destination

is there a command in unix/linux that allows you to sample what the historic byte rate is from a local IP to a client IP.

2. IP Networking

Selecting interface based on source and destination ip address

Hi all, I have some doubts in selecting the interface to transfer packets and receive the packets. --> Multiple interfaces : -------------------- 1) 0.0.0.0 --------> wild card address. 2) x.x.x.x --------> valid address.(192.168.1.156) 3) ff.ff.ff.ff -------->...

3. Shell Programming and Scripting

Move all files from source to destination directory based on the filename

Move all files starting with a specific name to different directory. This shell script program should have three parameters File Name Source Directory Destination Directory User should be able to enter �AB_CD*' in file name parameter. In this case all the files starting with AB_CD will...

4. Linux

rpmbuild, how to specify a different source and destination path for files

I'd like to specify a different build and deployment path for files, by default the same path is used for both build and install, I wasn't able to find a way to make these different. With Solaris pkgadd, one can specify different paths in prototype, so I would assume something like that is possible...

5. Solaris

Ftp: SSL_connect error while connecting from source to destination server Solaris 10

Hi Everyone, I am using solaris 10.I am facing a different problem here with tlsftp.I have intalled all steps for tlsftp and able to connect to the destination server from the source server.It worked for some days.But recently when i am connectin it is giving below error.I am...

6. UNIX for Advanced & Expert Users

Rsync error while running from destination to source

hi All, i have 2 server setup now for Rsync, i configured Rsync on both of the server and it worked well when i did run from source to destination. and while running back from destination to source it produced this error: bash-3.2$ ksh rsync_bravo_db.ksh usa0300uz1247.apps.mc.xerox.com...

7. Shell Programming and Scripting

Error files count while coping files from source to destination locaton as well count success full

hi All, Any one answer my requirement. I have source location src_dir="/home/oracle/arun/IRMS-CM" My Target location dest_dir="/home/oracle/arun/LiveLink/IRMS-CM/$dc/$pc/$ct" my source text files check with below example.text file content $fn "\t" $dc "\t" $pc "\t" ...

8. Shell Programming and Scripting

Count the number of files copied from source to destination location

Hi Guys, how to count number of files successfully copied while coping files from source to destination path ex:10 files from source to target location copying if 8 files copied successfully then echo successfully copied=8 failure=2 files if two files get error to coping files from...

9. UNIX for Beginners Questions & Answers

Open ports from source to destination

Is there a way to find out all the ports open between source IP & destination IP in any way ?

LEARN ABOUT FREEBSD

ucblinks

ucblinks(1B)					     SunOS/BSD Compatibility Package Commands					      ucblinks(1B)

NAME

       ucblinks - adds /dev entries to give SunOS 4.x compatible names to SunOS 5.x devices

SYNOPSIS

       /usr/ucb/ucblinks [-e rulebase] [-r rootdir]

DESCRIPTION

       ucblinks  creates symbolic links under the /dev directory for devices whose SunOS 5.x names differ from their SunOS 4.x names. Where possi-
       ble, these symbolic links point to the device's SunOS 5.x name rather than to the actual /devices entry.

       ucblinks does not remove unneeded compatibility links; these must be removed by hand.

       ucblinks should be called each time the system is reconfiguration-booted, after any new SunOS 5.x links that are needed have been  created,
       since the reconfiguration may have resulted in more compatibility names being needed.

       In  releases prior to SunOS 5.4, ucblinks used a  nawk rule-base to construct the SunOS 4.x compatible names. ucblinks no longer uses  nawk
       for the default operation, although  nawk rule-bases can still be specifed with the -e option.  The  nawk rule-base equivalent to the SunOS
       5.4 default operation can be found in /usr/ucblib/ucblinks.awk.

OPTIONS

       -e rulebase     Specify rulebase as the file containing nawk(1) pattern-action statements.

       -r rootdir      Specify rootdir as the directory under which dev and devices will be found, rather than the standard root directory /.

FILES

       /usr/ucblib/ucblinks.awk        sample rule-base for compatibility links

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWscpu			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       devlinks(1M), disks(1M), ports(1M), tapes(1M), attributes(5)

SunOS 5.10							    13 Apr 1994 						      ucblinks(1B)