rpcbind failure Post: 302212612

10 More Discussions You Might Find Interesting

1. SCO

rpcbind errors

HI, During the system bootup, following errors are being logged in "syslog" i) unix1 rpcbind: netdir_getbyname failed on tcp for host unix1, se rvice rpcbind ii)unix1 rpcbind: netdir_getbyname failed on udp for host unix1, se rvice rpcbind iii)unix1 in.snmpd: unix1: Host unknown. ...

2. UNIX for Dummies Questions & Answers

rpcbind / info Problem

I'm just going to throw this out there because I have no clue what is causing this problem or how to fix it. selinux is not enabled nor is any sort of firewall. (To my knowledge -- I did a kickstart install with firewall --disabled ) # rpcinfo program version netid address ...

3. Linux

RPCBIND Hang at Boot

Hi guys, i explain my problem: I've FC10 64bit installed on a server Dell R410. When i boot the system with eth0 or eth1 linked (only one eth linked), all work fine and the system start normally. When i boot the system with eth0 + eth1 linked, the system hang when the rpcind service...

4. Solaris

RPC: Rpcbind failure - RPC: Timed out

while i trying to mount from NAS i have this messages mount -F nfs -o rw 172.16.110.13:/tremabkup /tremabkup nfs mount: 172.16.110.13: : RPC: Rpcbind failure - RPC: Timed out nfs mount: retrying: /tremabkup nfs mount: 172.16.110.13: : RPC: Rpcbind failure - RPC: Timed out nfs mount:...

5. Solaris

Error : "RPC: Rpcbind failure - RPC: Timed out"

Hello I am having an issue with a server SUN FIRE T2000 (Solaris 10). First of all the server didn't boot normaly so I did a full restoration of the file systems. Now the server boot, most of the services are available (not all the services), but I keep on seeing RPC: Rpcbind failure -...

6. Solaris

RPC: Rpcbind failure - RPC: Timed out error (solaris)

C: Rpcbind failure - RPC: Timed out error (solaris) hello an nfs server on my sun fire v440 is not responding , i get the error bellow and lots of my networking services are not reponding, please helppppp its an emergency RPC: Rpcbind failure - RPC: Timed out i also get NFS server...

7. UNIX for Dummies Questions & Answers

boot up failure unix sco after power failure

hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless.

8. Solaris

nfs mount: RPC: Rpcbind failure - RPC: Timed out

Fails to mount the server (10.125.224.22) during installation of a software on client, throwing the below error: nfs mount: 10.125.224.22: : RPC: Rpcbind failure - RPC: Timed out nfs mount: retrying: /cdrom This happened after complete shutdown of the lab. The server came up fine but most...

9. Ubuntu

NIS/RPCBind Conflict!

Hi I am trying to configure NIS client on my Ubuntu 12.04. But I could not put portmap without uninstalling rpcbind. Do I need to have rpcbind there on the server, or how can I have both portmap and rpcbind at same time there on the server, because it's having conflict.

10. Solaris

Rpcbind service not starting

Hello all, I have read just about every rpcbind not starting thread and article on the internet it seems, but I have not found a solution to my problem as of yet. I have a solaris 10 server that has been running with no problems for a while. The other day it crashed and would not boot to the gui...

LEARN ABOUT FREEBSD

rup

RUP(1)							    BSD General Commands Manual 						    RUP(1)

NAME

     rup -- remote status display

SYNOPSIS

     rup [host ...]

DESCRIPTION

     The rup utility displays a summary of the current system status of a particular host or all hosts on the local network.  The output shows the
     current time of day, how long the system has been up, and the load averages.  The load average numbers give the number of jobs in the run
     queue averaged over 1, 5 and 15 minutes.

     The rpc.rstatd(8) daemon must be running on the remote host for this command to work.  The rup utility uses an RPC protocol defined in
     <rpcsvc/rstat.x>.

EXAMPLES

     example% rup otherhost
     otherhost	 7:36am  up 6 days, 16:45,  load average: 0.20, 0.23, 0.18
     example%

DIAGNOSTICS

     rup: RPC: Program not registered  The rpc.rstatd(8) daemon has not been started on the remote host.

     rup: RPC: Timed out  A communication error occurred.  Either the network is excessively congested, or the rpc.rstatd(8) daemon has terminated
     on the remote host.

     rup: RPC: Port mapper failure - RPC: Timed out  The remote host is not running the portmapper (see rpcbind(8)), and cannot accommodate any
     RPC-based services.  The host may be down.

SEE ALSO

     rpc.rstatd(8), rpcbind(8)

HISTORY

     The rup command appeared in Sun-OS.

BUGS

     The sorting options are not implemented.

BSD
								   June 7, 1993 							       BSD