07-05-2008
post some more information about your system....
df -h
format | echo
vxprint -ht
8 More Discussions You Might Find Interesting
1. IP Networking
I have Linux 7.1 setup on a Dell and am unable to bring up any interfaces. Both the lo and eth0 fail upon boot up and I get a insmod error possibly due to bad irq or IO setting.
If I disable eth0 upon boot, then lo works fine, but offcourse I get the "delaying initialization" upon boot for eth0... (1 Reply)
Discussion started by: alam
1 Replies
2. UNIX for Dummies Questions & Answers
The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies
3. Red Hat
Hello,
I have few HDD and SSD installed in my RHEL 5 server. I want to know which disk are SDD and which are HDD. What command should I use?
Thanks (3 Replies)
Discussion started by: fahdmirza
3 Replies
4. Linux
Hi Guys,
I want to bring my server live.
I have Static public IP Address 123.99.88.77 (Say) and also I have also registered a domain name say(live server23.com) the domain name providers have also given me the control panel with DNS management settings.
I have gateway 192.168.1.1
Now My... (1 Reply)
Discussion started by: manalisharmabe
1 Replies
5. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
6. Solaris
this is samiulla
in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance
and i am unable to bring into online with svcadm clear iscsitgt
how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies
7. Shell Programming and Scripting
Hi Experts,
Problem summary :
I am facing the below problem on huge files when the disk is getting full on the half way through the execution.
If the disk was already full , the commands fail & everything is fine.
Sample Code :
head_rec_data_file=`head -1 sample_file.txt`
cat... (9 Replies)
Discussion started by: Pruthviraj_shiv
9 Replies
8. AIX
Hi all, I have the following in hacmp.out for bringing Resource group online.
Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems.
+main1_rg_01:cl_activate_vgs STATUS=0
+main1_rg_01:cl_activate_vgs typeset -li STATUS
+main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies
LEARN ABOUT HPUX
vxreattach
vxreattach(1M) vxreattach(1M)
NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS
-b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO
vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)
VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)