Sponsored Content
Full Discussion: Network problem
Special Forums IP Networking Network problem Post 302209784 by Katkota on Saturday 28th of June 2008 11:32:22 AM
Old 06-28-2008
OK, two things here:
1. I'm not sure about the "hop the target" part. could you please explain a little more?

-The second thing is i had some doubts about my SSH package so i reinstalled it. After that i was able to ssh between both for a little while, then it went back to the same issue.

Now this is to me is very strange & i don't understand this behavior.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Network problem Unix

Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange? Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies

2. Solaris

Network problem.

Hi All, This is regarding problem with two servers... EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX) But we can able to login.... server1 is not able to pickup any data from the proxy server... checked in the sunbox... # ping bdhp5050 server1 is alive ... (1 Reply)
Discussion started by: jeelans
1 Replies

3. SCO

Network interfaces problem

Hi, I have problems with my SCO unix network interfaces. Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot. Installed driver using SCO Software manager - successfully Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies

4. AIX

network printer problem

I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect. what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies

5. Solaris

Problem in network configuration

Hi everybody, I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem. I have 2 unix machines absolutely identical running solaris 9. For network reasons I need to change the IP address of the 2 machines. I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies

6. AIX

AIX OS problem? network problem?

Dear ALL. I installed AIX OS on customer sites. but Only one site is too slow when I connected telnet, ftp.. Ping is too fast. but telnet and FTP is not connected.. of course i check the configuration file on aix but it's normal. Do any Idea?? thanks in advance. - Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies

7. Solaris

Network interface problem

Hi i have replace a NIC card on solaris 10 when i give the following command ifconfig -a it just show the lo0 (only loop back with inet 127.0.0.1) when i give the following command to config the interface, ifconfig elxl0 plumb ifconfig: plumb: elxl0: no such interface please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies

8. AIX

Network Problem

Hi everbody; I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
Discussion started by: lordofdarkness
2 Replies

9. Debian

/etc/network/interfaces problem

Hello i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address then i save it wq! then i restart the networking , /etc/init.d/networking restart . but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies

10. Android

Problem with wireless network

Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
AGGREGATE-IOS(1)					      General Commands Manual						  AGGREGATE-IOS(1)

NAME
aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short. SYNOPSIS
aggregate-ios <source_config >optimised_config DESCRIPTION
Takes cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1). Optimised filters are produced on std- out. OPTIONS
None. DIAGNOSTICS
Any diagnostics produced by aggregate(1) are passed through on stderr. EXAMPLES
The following configuration fragment: ip prefix-list AS65530 description Foo, Inc ip prefix-list AS65530 permit 10.1.0.0/16 ip prefix-list AS65530 permit 10.2.0.0/16 ip prefix-list AS65530 permit 10.2.1.0/24 ip prefix-list AS65530 permit 10.3.0.0/16 ip prefix-list AS65531 description Bar.Com ip prefix-list AS65531 seq 5 permit 192.168.1.0/24 ip prefix-list AS65531 seq 10 permit 192.168.2.0/24 ip prefix-list AS65531 seq 15 permit 192.168.0.0/19 is optimised as follows: ip prefix-list AS65530 permit 10.1.0.0/16 le 24 ip prefix-list AS65530 permit 10.2.0.0/15 le 24 ip prefix-list AS65531 permit 192.168.0.0/19 le 24 SEE ALSO
aggregate(1) HISTORY
Aggregate-ios was written by Joe Abley <jabley@mfnx.net>. BUGS
All those in aggregate(1) and then some :) Joe Abley 2000 November 27 AGGREGATE-IOS(1)
All times are GMT -4. The time now is 05:23 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy