Hi
I have a list of files in a folder.I have a search pattern in the file name and i want to remove the file with that pattern.How can that be made
List of files
xxxxx.ID1.yyyyy.zzzzz
yyyy.ID2.bbbbb.kkkkk
xxxxx.ID1.yyyyy.zzzzz
yyyy.ID4.bbbbb.kkkkk
xxxxx.ID1.yyyyy.zzzzz... (2 Replies)
Helo ,
I m writing small module of c.on RHEL 4
I have one buffer (for e.g. buffer = "002"
now I want to check whethere buffer contains leading zeroes and if it contains
leading zeroes then I want to remove all leading zeroes
( i.e. if buffer = "002" then I want to make buffer = "2")
how... (1 Reply)
Hi all,
I have a text data file. My aim here is to find line called *FIELD* AV for every record and print lines after that till *FIELD* RF. But here I want first 3 to four lines for very record as well. FIELD AV is some where in between for very record. SO I am not sure how to retrieve lines in... (2 Replies)
Hi all,
I have a big file (n.txt) with following pattern:
ATOM 1 N SER A 1 122.392 152.261 138.190 1.00 0.00 N
ATOM 2 CA SER A 1 122.726 151.241 139.183 1.00 0.00 C
TER
ENDMDL
ATOM 1 N SER A 1 114.207 142.287 135.439 1.00 0.00 ... (3 Replies)
I have a file with entries below.
domain1.com.http:
domain2.com.49503:
I need this to be sorted like below. ie remove the patten after the last right-hand side . (dot).
domain1.com
domain2.com (7 Replies)
Hi,
I want to search a pattern in a text file and remove another pattern in that file.
my text file look like this
0.000000 1.970000 F 303 -
1.970000 2.080000 VH VH +
2.080000 2.250000 VH VH +
2.250000 2.330000 VH L -
2.330000 2.360000 F H +
2.360000 2.410000 L VL -
2.410000 ... (6 Replies)
Hi I have a file where i want to remove a char before a specific pattern.
exp:
CREATE TABLE
(
A,
B,
C, ----comma needs to be removed
)AS SELECT
A,
B,
C, ----comma needs to be removed
FROM TABLE.
So i want to delete the comma(,) after the C both ways.Pattern can be... (11 Replies)
In the awk below I am trying to remove all lines above and including the pattern Test or Test2. Each block is seperated by a newline and Test2 also appears in the lines to keep but it will always have additional text after it. The Test to remove will not. The awk executed until the || was added... (2 Replies)
Discussion started by: cmccabe
2 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)