Sponsored Content
Full Discussion: failover on 4.5 hacmp
Operating Systems AIX failover on 4.5 hacmp Post 302208704 by itik on Tuesday 24th of June 2008 03:23:21 PM
Old 06-24-2008
failover on 4.5 hacmp

Hi All,

How do I trigger the failover on the second hacmp server?

Please give me idea and I will do the rest.

Thanks,
itik
 

10 More Discussions You Might Find Interesting

1. Solaris

Interfaces do not failover

Would anyone know why a V440 Solaris 9 machine's interfaces (ce0 and ce1) will not failover? Both interfaces are on the same subnet, but different IPs. I can pull the plug on once interface (ce0) and ce1 will be accessible. I can reverse it and pull ce1, and ce0 will NOT be accessible. ... (5 Replies)
Discussion started by: StorageGuy
5 Replies

2. AIX

Can anyone shed some light on this HACMP failover?

Hello All, Here is a snipet from our cluster.log, I was wondering if anyone could shed some light on what may have caused the failover. The first two lines indicate a possible memory issue which I am currently looking into. Thanks. (0 Replies)
Discussion started by: Wez
0 Replies

3. UNIX for Advanced & Expert Users

directories failover

Hi, I have 3 directories (/1 /2 and /3) with same contents and want to achieve fail over among them. The Solution i thought of: 1. link /data to /1 (and provide users with /data to access) 2. CRON a script (to run every minute) to verify if /1 exist or not, if it does not exist (or its... (3 Replies)
Discussion started by: prvnrk
3 Replies

4. AIX

hacmp ip load balancer failover

Hi All, How do I failover on the ip load balancer (back and forth)? It involves first to load a new config on the passive ip. If success, load the new config on the ip active (which is now passive). Any idea, please. Thanks in advance. (0 Replies)
Discussion started by: itik
0 Replies

5. Solaris

IPMP failover: Why is it occurring?

The active NIC has been failing back and forth on two of our T2000s. I don't know when the problem originally began, but I can see failovers in the messages.* files. The network guy says the switches are clean (no errors) so I'm left looking at the configuration or any other issue that may be... (5 Replies)
Discussion started by: dangral
5 Replies

6. Solaris

EMC Failover

Hi guys, I'm running vxdmp and powerpath at the same time. Vxdmp for internal disks and powerpath for external. The problem is that, on the failover tests which a fiber cable should be removed, the system cannot recognize the disks. Any hints on how to configure powerpath in order to... (4 Replies)
Discussion started by: glenioborges
4 Replies

7. IP Networking

IP failover needed

All, I am looking to setup a simple IP failover setup, but it seems every place i look has some difficult setup like pacemaker or LVS. I only want to handle the IP piece to failover a VIP. Any suggestions? I checked out keepalived and that my work for me. (4 Replies)
Discussion started by: markdjones82
4 Replies

8. Gentoo

How to failover the cluster ?

How to failover the cluster ? GNU/Linux By which command, My Linux version 2008 x86_64 x86_64 x86_64 GNU/Linux What are the prerequisites we need to take while failover ? if any Regards (3 Replies)
Discussion started by: sidharthmellam
3 Replies

9. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies

10. AIX

HACMP with VIO, service IP failover

Would anyone please kindly help to solve this problem... An LPAR with the below network configuration. ent0 and ent1 are logical lan (virtual ethernet) from VIO SEA. en0 1.2.3.4 <- boot ip 192.168.1.1 <- persistent ip 192.168.1.10 <- service ip en1 11.22.33.44 <- boot ip When I... (6 Replies)
Discussion started by: skeyeung
6 Replies
ALTER 
TRIGGER(7) SQL Commands ALTER TRIGGER(7) NAME
ALTER TRIGGER - change the definition of a trigger SYNOPSIS
ALTER TRIGGER name ON table RENAME TO newname DESCRIPTION
ALTER TRIGGER changes properties of an existing trigger. The RENAME clause changes the name of the given trigger without otherwise changing the trigger definition. You must own the table on which the trigger acts to be allowed to change its properties. PARAMETERS
name The name of an existing trigger to alter. table The name of the table on which this trigger acts. newname The new name for the trigger. NOTES
The ability to temporarily enable or disable a trigger is provided by ALTER TABLE [alter_table(7)], not by ALTER TRIGGER, because ALTER TRIGGER has no convenient way to express the option of enabling or disabling all of a table's triggers at once. EXAMPLES
To rename an existing trigger: ALTER TRIGGER emp_stamp ON emp RENAME TO emp_track_chgs; COMPATIBILITY
ALTER TRIGGER is a PostgreSQL extension of the SQL standard. SEE ALSO
ALTER TABLE [alter_table(7)] SQL - Language Statements 2010-05-14 ALTER TRIGGER(7)
All times are GMT -4. The time now is 08:18 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy